[Letux-kernel] [PATCH v8 6/8] MIPS: DTS: CI20: Add DT nodes for HDMI setup

H. Nikolaus Schaller hns at goldelico.com
Wed Nov 24 17:19:09 CET 2021



> Am 23.11.2021 um 21:10 schrieb Paul Cercueil <paul at crapouillou.net>:
> 
> Hi Nikolaus,
> 
> Le mar., nov. 23 2021 at 19:13:59 +0100, H. Nikolaus Schaller <hns at goldelico.com> a écrit :
>> From: Paul Boddie <paul at boddie.org.uk>
>> We need to hook up
>> * HDMI connector
>> * HDMI power regulator
>> * JZ4780_CLK_HDMI @ 27 MHz
>> * DDC pinmux
>> * HDMI and LCDC endpoint connections
>> Signed-off-by: Paul Boddie <paul at boddie.org.uk>
>> Signed-off-by: H. Nikolaus Schaller <hns at goldelico.com>
>> ---
>> arch/mips/boot/dts/ingenic/ci20.dts | 83 +++++++++++++++++++++++++++--
>> 1 file changed, 80 insertions(+), 3 deletions(-)
>> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
>> index b249a4f0f6b62..15cf03670693f 100644
>> --- a/arch/mips/boot/dts/ingenic/ci20.dts
>> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
>> @@ -78,6 +78,18 @@ eth0_power: fixedregulator at 0 {
>> 		enable-active-high;
>> 	};
>> +	hdmi_out: connector {
>> +		compatible = "hdmi-connector";
>> +		label = "HDMI OUT";
>> +		type = "a";
>> +
>> +		port {
>> +			hdmi_con: endpoint {
>> +				remote-endpoint = <&dw_hdmi_out>;
>> +			};
>> +		};
>> +	};
>> +
>> 	ir: ir {
>> 		compatible = "gpio-ir-receiver";
>> 		gpios = <&gpe 3 GPIO_ACTIVE_LOW>;
>> @@ -102,6 +114,17 @@ otg_power: fixedregulator at 2 {
>> 		gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
>> 		enable-active-high;
>> 	};
>> +
>> +	hdmi_power: fixedregulator at 3 {
>> +		compatible = "regulator-fixed";
>> +
>> +		regulator-name = "hdmi_power";
>> +		regulator-min-microvolt = <5000000>;
>> +		regulator-max-microvolt = <5000000>;
>> +
>> +		gpio = <&gpa 25 0>;
>> +		enable-active-high;
>> +	};
>> };
>> &ext {
>> @@ -114,11 +137,13 @@ &cgu {
>> 	 * precision.
>> 	 */
>> 	assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>,
>> -			  <&cgu JZ4780_CLK_SSIPLL>, <&cgu JZ4780_CLK_SSI>;
>> +			  <&cgu JZ4780_CLK_SSIPLL>, <&cgu JZ4780_CLK_SSI>,
>> +			  <&cgu JZ4780_CLK_HDMI>;
>> 	assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>,
>> 				 <&cgu JZ4780_CLK_MPLL>,
>> -				 <&cgu JZ4780_CLK_SSIPLL>;
>> -	assigned-clock-rates = <48000000>, <0>, <54000000>;
>> +				 <&cgu JZ4780_CLK_SSIPLL>,
>> +				 <0>;
> 
> Nit - you can remove the last <0>, it will be the default.

Well, it might make life easier for the next addition but I've removed it.

> 
>> +	assigned-clock-rates = <48000000>, <0>, <54000000>, <0>, <27000000>;
>> };
>> &tcu {
>> @@ -509,6 +534,19 @@ pins_i2c4: i2c4 {
>> 		bias-disable;
>> 	};
>> +	pins_hdmi_ddc: hdmi_ddc {
>> +		function = "hdmi-ddc";
>> +		groups = "hdmi-ddc";
>> +		bias-disable;
>> +	};
>> +
>> +	/* switch to PF25 as gpio driving DDC_SDA low */
>> +	pins_hdmi_ddc_unwedge: hdmi_ddc {
>> +		function = "hdmi-ddc";
>> +		groups = "hdmi-ddc";
>> +		bias-disable;
>> +	};
> 
> Your pins_hdmi_ddc and pins_hdmi_ddc_unwedge are the exact same? You could just use the former and pass it to both pinctrl-0 and pinctrl-1.

This was forgotten to remove. We do not make use of the unwedge feature because I could not find out how to use pinctrl to switch this to gpio25 and drive it low.
And I always had a revert for this in my test tree and we haven't seen a stuck DDC so far. Therefore I remove it (and leave it as maybe-to-to in my tree).

> 
> Cheers,
> -Paul
> 
>> +
>> 	pins_nemc: nemc {
>> 		function = "nemc";
>> 		groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe";
>> @@ -539,3 +577,42 @@ pins_mmc1: mmc1 {
>> 		bias-disable;
>> 	};
>> };
>> +
>> +&hdmi {
>> +	status = "okay";
>> +
>> +	pinctrl-names = "default", "unwedge";
>> +	pinctrl-0 = <&pins_hdmi_ddc>;
>> +	pinctrl-1 = <&pins_hdmi_ddc_unwedge>;
>> +
>> +	hdmi-5v-supply = <&hdmi_power>;
>> +
>> +	ports {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		port at 0 {
>> +			reg = <0>;
>> +			dw_hdmi_in: endpoint {
>> +				remote-endpoint = <&lcd_out>;
>> +			};
>> +		};
>> +
>> +		port at 1 {
>> +			reg = <1>;
>> +			dw_hdmi_out: endpoint {
>> +				remote-endpoint = <&hdmi_con>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&lcdc0 {
>> +	status = "okay";
>> +
>> +	port {
>> +		lcd_out: endpoint {
>> +			remote-endpoint = <&dw_hdmi_in>;
>> +		};
>> +	};
>> +};
>> --
>> 2.33.0



More information about the Letux-kernel mailing list