[Letux-kernel] [PATCH] usb: musb: Check devctl status again for a spurious session request

[Andreas Kemnade]

On Fri, 4 Jun 2021 12:39:54 +0300
Tony Lindgren <tony at atomide.com> wrote:

> * Andreas Kemnade <andreas at kemnade.info> [210604 08:35]:
> > I inserted some more dev-dbg
> > [   60.241790] PM: suspend entry (deep)
> > [   60.245513] Filesystems sync: 0.000 seconds
> > [   60.251312] Freezing user space processes ... (elapsed 0.001 seconds) done.
> > [   60.260040] OOM killer disabled.
> > [   60.263275] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
> > [   60.272338] printk: Suspending console(s) (use no_console_suspend to debug)
> > [   60.281311] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_resume  
> > -> this is triggered by what?  
> 
> I think that comes from the pm_runtime_get_sync() in musb_suspend().
> 
@@ -2825,6 +2826,7 @@ static int musb_suspend(struct device *dev)
        struct musb     *musb = dev_to_musb(dev);
        unsigned long   flags;
        int ret;
+       dev_dbg(musb->controller, "musb_suspend begin\n");
 
        ret = pm_runtime_get_sync(dev);
        if (ret < 0) {

my dev_dbg comes before that.

> > [   60.281341] twl4030_usb 48070000.i2c:twl at 48:twl4030-usb: twl4030_usb_runtime_resume  
> > -> and here something stays on...  
> > 
> > [   60.346374] twl4030_usb 48070000.i2c:twl at 48:twl4030-usb: twl4030_phy_power_on
> > [   60.796630] musb-hdrc musb-hdrc.0.auto: musb_suspend begin
> > [   60.796722] musb-hdrc musb-hdrc.0.auto: musb_suspend end
> > [   60.796752] musb-omap2430 480ab000.usb_otg_hs: omap2430 suspend
> > [   60.796783] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_suspend
> > [   60.796783] twl4030_usb 48070000.i2c:twl at 48:twl4030-usb: twl4030_phy_power_off
> > [   60.796813] twl4030_usb 48070000.i2c:twl at 48:twl4030-usb: twl4030_usb_suspend
> > [   60.806549] Disabling non-boot CPUs ...
> > [   60.806579] Successfully put all powerdomains to target state  
> 
> Well since commit 88d26136a256 ("PM: Prevent runtime suspend during system resume")
> nothing gets runtime idled during suspend with the extra pm_runtime_get_noresume()
> call in device_prepare() that does not get released until in device_complete().
> 
well, the result is that the phy stays powered on. And that is the
problem.
static int twl4030_phy_power_off(struct phy *phy)
and 
static int __maybe_unused twl4030_usb_suspend(struct device *dev)
do not turn off the phy. I think the solution is to turn the phy off if
no cable is connected. 

> > forcing omap2430 runtime on before suspend:
> > [  160.467742] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_resume
> > [  165.001495] PM: suspend entry (deep)
> > [  165.005218] Filesystems sync: 0.000 seconds
> > [  165.010284] Freezing user space processes ... (elapsed 0.001 seconds) done.
> > [  165.018981] OOM killer disabled.
> > [  165.022247] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
> > [  165.031311] printk: Suspending console(s) (use no_console_suspend to debug)
> > [  165.040496] musb-hdrc musb-hdrc.0.auto: musb_suspend begin
> > [  165.040618] musb-hdrc musb-hdrc.0.auto: musb_suspend end
> > [  165.040618] musb-omap2430 480ab000.usb_otg_hs: omap2430 suspend
> > [  165.040649] musb-omap2430 480ab000.usb_otg_hs: omap2430 runtime_suspend
> > [  165.040679] twl4030_usb 48070000.i2c:twl at 48:twl4030-usb: twl4030_usb_suspend
> > [  165.050506] Disabling non-boot CPUs ...
> > [  165.050537] Successfully put all powerdomains to target state  
> 
> That's interesting. Hmm so we bail out early based on glue->is_runtime_suspended,
> and omap3 is still probing devices with omap_device.c instead of ti-sysc.c, so
> sounds like the duplicate calls you noticed might cause the issue.
> 
> Does the following patch fix things for you or does something else break again? :)
> 
looks like something I have already tried, but I will give it a look
again.

Regards,
Andreas