[Letux-kernel] BeagleBoard XM OpenMoko Hyprid (bb+b1) is booting with 2016-11 U-Boot :)
H. Nikolaus Schaller
hns at goldelico.com
Tue Dec 13 20:29:20 CET 2016
> Am 12.12.2016 um 22:05 schrieb H. Nikolaus Schaller <hns at goldelico.com>:
>
>
> I had to fix the Makefile for the bb+b1 variant.
> Although it reports some errors, the boot.scr shows the boot menu
> and if I choose to boot from partition 1, I get the 4.9.0 kernel
> up and running :)
I have found some issues (mainly with RAM initialization) for the GTA04
board code and now SPL works while U-Boot starts and is then stuck:
U-Boot SPL 2016.11-00141-gcc48556-dirty (Dec 13 2016 - 20:07:42)
Trying to boot from MMC1
board_mmc_power_init
Found GTA04A3
pop_mfr = 2c pop_id = bc
reading u-boot.img
reading u-boot.img
U-Boot 2016.11-00141-gcc48556-dirty (Dec 13 2016 - 20:07:42 +0100)
OMAP3630/3730-GP ES1.2, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
GTA04 + LPDDR/NAND
I2C: ready
DRAM: 1 GiB
show_boot_progress
NAND: 512 MiB
MMC: board_mmc_init !SPL
OMAP SD/MMC: 0
Error: Bad compare! failed
Error: Bad compare! failed
Error: Bad compare! failed
NAND read from offset 260000 failed -74
*** Warning - readenv() failed, using default environment
misc_init_r
Found GTA04A3
Device Tree: omap3-gta04a3
OMAP die ID: 166600029ff800000163810c17036010
Even if it does not yet boot through to Linux (maybe it has something to do with the wrong RAM size detection), this is big progress since Sunday.
I still have to clean up the commits and push. And fix the u-boot for Letux 3704 and Letux 7004.
BR,
Nikolaus
>
> U-Boot SPL 2016.11-00137-g599f9dd-dirty (Dec 12 2016 - 19:59:26)
> Trying to boot from MMC1
> SPL: Please implement spl_start_uboot() for your board
> SPL: Direct Linux boot not active!
> reading u-boot.img
> reading u-boot.img
>
>
> U-Boot 2016.11-00137-g599f9dd-dirty (Dec 12 2016 - 19:59:26 +0100)
>
> OMAP3630/3730-GP ES1.1, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
> OMAP3 Beagle board + LPDDR/NAND
> I2C: ready
> DRAM: 512 MiB
> NAND: 0 MiB
> MMC: OMAP SD/MMC: 0
> *** Warning - readenv() failed, using default environment
>
> misc_init_r
> Beagle xM Rev A/B
> No EEPROM on expansion board
> OMAP die ID: 36fc00019ff80000015eeaa10202d00c
> board revision 0
> Device Tree: omap3-beagle-xm-ab+gta04b1
> Net: usb_ether
> Error: usb_ether address not set.
>
> Hit any key to stop autoboot: 0
> switch to partitions #0, OK
> mmc0 is current device
> gpio: pin 173 (gpio 173) value is 0
> gpio: pin 4 (gpio 4) value is 0
> SD/MMC found on device 0
> reading uEnv.txt
> ** Unable to read file uEnv.txt **
> reading boot.scr
> 14649 bytes read in 5 ms (2.8 MiB/s)
> Running bootscript from mmc0 ...
> ## Executing script at 80200000
> *** if you boot from NAND don-t worry about error messages when U-Boot tries to read a non-existing MMC ***
> Setting bus to 0
> did init LED driver for TCA6507
> *** initializing GTA04 environment ***
>
> no devices available
> can not flash - must always boot from SD card
> *** initializing LCM ***
> board_video_init() for JBT6K74-AS / TD028TTEC1
> did backlight_init() on GPIO_145
> i2c_write: error waiting for addr ACK (status=0x116)
> Could not write vsel to reg 75 (1)
> did panel_reg_init()
> dss panel config
> dss enable
> did board_video_init()
> did jbt_init_regs()
> lcm backlight level set to 255 (0..255)
> *** loading splash from MMC ***
> Setting bus to 0
> mmc - MMC sub system
>
> Usage:
> mmc info - display info of the current MMC device
> mmc read addr blk# cnt
> mmc write addr blk# cnt
> mmc erase blk# cnt
> mmc rescan
> mmc part - lists available partition on current mmc device
> mmc dev [dev] [part] - show or set current mmc device [partition]
> mmc list - lists available devices
> mmc hwpartition [args...] - does hardware partitioning
> arguments (sizes in 512-byte blocks):
> [user [enh start cnt] [wrrel {on|off}]] - sets user data area attributes
> [gp1|gp2|gp3|gp4 cnt [enh] [wrrel {on|off}]] - general purpose partition
> [check|set|complete] - mode, complete set partitioning completed
> WARNING: Partitioning is a write-once setting once it is set to complete.
> Power cycling is required to initialize partitions after set to complete.
> mmc setdsr <value> - set DSR register value
>
> reading splash.rgb16
> ** Unable to read file splash.rgb16 **
> reading splash.rgb16z
> 39304 bytes read in 7 ms (5.4 MiB/s)
> Uncompressed size: 614400 = 0x96000
> *** initializing TSC for boot menu ***
> ITG3200 does not respond
> i2c_write: error waiting for addr ACK (status=0x116)
> Could not write vsel to reg 79 (1)
> i2c_write: error waiting for addr ACK (status=0x116)
> Could not write vsel to reg 79 (1)
> ITG3200 still does not respond
> did tsc2007_init()
> *** loading boot menu image ***
> Setting bus to 0
> mmc - MMC sub system
>
> Usage:
> mmc info - display info of the current MMC device
> mmc read addr blk# cnt
> mmc write addr blk# cnt
> mmc erase blk# cnt
> mmc rescan
> mmc part - lists available partition on current mmc device
> mmc dev [dev] [part] - show or set current mmc device [partition]
> mmc list - lists available devices
> mmc hwpartition [args...] - does hardware partitioning
> arguments (sizes in 512-byte blocks):
> [user [enh start cnt] [wrrel {on|off}]] - sets user data area attributes
> [gp1|gp2|gp3|gp4 cnt [enh] [wrrel {on|off}]] - general purpose partition
> [check|set|complete] - mode, complete set partitioning completed
> WARNING: Partitioning is a write-once setting once it is set to complete.
> Power cycling is required to initialize partitions after set to complete.
> mmc setdsr <value> - set DSR register value
>
> reading menu.rgb16
> ** Unable to read file menu.rgb16 **
> reading menu.rgb16z
> 247281 bytes read in 22 ms (10.7 MiB/s)
> Uncompressed size: 614400 = 0x96000
> Choosing by waiting for touch.
> 1 2 3
> 4 5 6
> 7 8 9
> Press touch or any key to stop
>
> did choose 0/0 -> 1
> background color: 00ff00
> *** MMC boot partition 1***
> new boot order 1 2 3 4
> Saving Environment to NAND...
> Setting bus to 0
> mmc - MMC sub system
>
> Usage:
> mmc info - display info of the current MMC device
> mmc read addr blk# cnt
> mmc write addr blk# cnt
> mmc erase blk# cnt
> mmc rescan
> mmc part - lists available partition on current mmc device
> mmc dev [dev] [part] - show or set current mmc device [partition]
> mmc list - lists available devices
> mmc hwpartition [args...] - does hardware partitioning
> arguments (sizes in 512-byte blocks):
> [user [enh start cnt] [wrrel {on|off}]] - sets user data area attributes
> [gp1|gp2|gp3|gp4 cnt [enh] [wrrel {on|off}]] - general purpose partition
> [check|set|complete] - mode, complete set partitioning completed
> WARNING: Partitioning is a write-once setting once it is set to complete.
> Power cycling is required to initialize partitions after set to complete.
> mmc setdsr <value> - set DSR register value
>
> trying partitions 1 2 3 4
> reading uImage
> 4610344 bytes read in 354 ms (12.4 MiB/s)
> found kernel /uImage on partition 1
> reading bootargs.scr
> 2108 bytes read in 4 ms (514.6 KiB/s)
> ## Executing script at 80800000
> running bootargs.scr
> bootargs.scr done...
> reading omap3-beagle-xm-ab+gta04b1.dtb
> 69104 bytes read in 11 ms (6 MiB/s)
> ## Booting kernel from Legacy Image at 82000000 ...
> Image Name: Linux-4.9.0-letux+
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 4610280 Bytes = 4.4 MiB
> Load Address: 80008000
> Entry Point: 80008000
> Verifying Checksum ... OK
> ## Flattened Device Tree blob at 81c00000
> Booting using the fdt blob at 0x81c00000
> Loading Kernel Image ... OK
> Using Device Tree in place at 81c00000, end 81c13def
>
> Starting kernel ...
>
> [ 0.000000] Booting Linux on physical CPU 0x0
> [ 0.000000] Linux version 4.9.0-letux+ (hns at iMac.local) (gcc version 4.9.2 (GCC) ) #518 SMP PREEMPT Mon Dec 12 21:06:05 CET 2016
> [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
> [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
> [ 0.000000] OF: fdt:Machine model: BeagleBoard XM / GTA04 b1 / OpenMoko-Beagle-Hybrid
> [ 0.000000] debug: ignoring loglevel setting.
> [ 0.000000] cma: Reserved 16 MiB at 0x9e800000
> [ 0.000000] Memory policy: Data cache writeback
> [ 0.000000] On node 0 totalpages: 130560
> [ 0.000000] free_area_init_node: node 0, pgdat c0c9de00, node_mem_map df9f1000
> [ 0.000000] Normal zone: 1024 pages used for memmap
> [ 0.000000] Normal zone: 0 pages reserved
> [ 0.000000] Normal zone: 130560 pages, LIFO batch:31
> [ 0.000000] CPU: All CPU(s) started in SVC mode.
> [ 0.000000] OMAP3630 ES1.1 (l2cache iva sgx neon isp 192mhz_clk)
> [ 0.000000] percpu: Embedded 15 pages/cpu @df99b000 s31680 r8192 d21568 u61440
> [ 0.000000] pcpu-alloc: s31680 r8192 d21568 u61440 alloc=15*4096
> [ 0.000000] pcpu-alloc: [0] 0
> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
> [ 0.000000] Kernel command line: console=ttyO2,115200n8 mtdoops.mtddev=omap2.nand ubi.mtd=4 root=/dev/mmcblk0p2 rw rootfstype=ext4,ext3 rootwait console=ttyO2,115200n8 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk
> [ 0.000000] log_buf_len: 8388608 bytes
> [ 0.000000] early log buf free: 63888(97%)
> [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
> [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> [ 0.000000] Memory: 472744K/522240K available (7168K kernel code, 654K rwdata, 2164K rodata, 1024K init, 8032K bss, 33112K reserved, 16384K cma-reserved, 0K highmem)
> [ 0.000000] Virtual kernel memory layout:
> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
> [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
> [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
> [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
> [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
> [ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB)
> [ 0.000000] .init : 0xc0b00000 - 0xc0c00000 (1024 kB)
> [ 0.000000] .data : 0xc0c00000 - 0xc0ca3930 ( 655 kB)
> [ 0.000000] .bss : 0xc0ca3930 - 0xc147bb14 (8033 kB)
> [ 0.000000] Running RCU self tests
> [ 0.000000] Preemptible hierarchical RCU implementation.
> [ 0.000000] RCU lockdep checking is enabled.
> [ 0.000000] Build-time adjustment of leaf fanout to 32.
> [ 0.000000] RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
> [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
> [ 0.000000] NR_IRQS:16 nr_irqs:16 16
> [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
> [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
> [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz
> [ 0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
> [ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns
> [ 0.000030] OMAP clocksource: 32k_counter at 32768 Hz
> [ 0.002136] Console: colour dummy device 80x30
> [ 0.002197] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
> [ 0.002197] ... MAX_LOCKDEP_SUBCLASSES: 8
> [ 0.002227] ... MAX_LOCK_DEPTH: 48
> [ 0.002227] ... MAX_LOCKDEP_KEYS: 8191
> [ 0.002258] ... CLASSHASH_SIZE: 4096
> [ 0.002258] ... MAX_LOCKDEP_ENTRIES: 32768
> [ 0.002288] ... MAX_LOCKDEP_CHAINS: 65536
> [ 0.002288] ... CHAINHASH_SIZE: 32768
> [ 0.002319] memory used by lock dependency info: 5167 kB
> [ 0.002319] per task-struct memory footprint: 1536 bytes
> [ 0.002380] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696)
> [ 0.105407] pid_max: default: 32768 minimum: 301
> [ 0.106048] Security Framework initialized
> [ 0.106231] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.106262] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
> [ 0.111602] CPU: Testing write buffer coherency: ok
> [ 0.113983] CPU0: thread -1, cpu 0, socket -1, mpidr 0
> [ 0.114074] Setting up static identity map for 0x80100000 - 0x80100058
> [ 0.205352] Brought up 1 CPUs
> [ 0.205383] SMP: Total of 1 processors activated (594.73 BogoMIPS).
> [ 0.205413] CPU: All CPU(s) started in SVC mode.
> [ 0.211273] devtmpfs: initialized
> [ 0.395812] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
> [ 0.398529] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
> [ 0.400665] driver_register 'ARM-CCI PMU'
> [ 0.401000] driver_register 'ARM-CCI'
> [ 0.401214] pinctrl core: initialized pinctrl subsystem
> [ 0.403808] driver_register 'reg-dummy'
> [ 0.404357] _regulator_do_enable regulator-dummy
> [ 0.409942] NET: Registered protocol family 16
> [ 0.424621] DMA: preallocated 256 KiB pool for atomic coherent allocations
> [ 0.546051] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp
> [ 0.549285] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp
> [ 0.710632] driver_register 'omap_gpio'
> [ 0.714447] driver_register 'syscon'
> [ 0.720947] driver_register 'dummy'
> [ 0.721649] driver_register 'omap-gpmc'
> [ 0.722167] driver_register 'omap_l3_smx'
> [ 0.722686] driver_register 'omap_l3_noc'
> [ 0.723999] Reprogramming SDRC clock to 400000000 Hz
> [ 0.759490] omap_gpio 48310000.gpio: could not find pctldev for node /ocp at 68000000/l4 at 48000000/scm at 2000/pinmux at a00/pinmux_gpio1_pins, deferring probe
> [ 0.778228] OMAP GPIO hardware version 2.5
> [ 0.848205] irq: no irq domain found for /ocp at 68000000/l4 at 48000000/scm at 2000/pinmux at 30 !
> [ 0.915222] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
> [ 0.915527] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
> [ 0.966125] No ATAGs?
> [ 0.966156] hw-breakpoint: debug architecture 0x4 unsupported.
> [ 0.968627] omap4_sram_init:Unable to allocate sram needed to handle errata I688
> [ 0.968688] omap4_sram_init:Unable to get sram pool needed to handle errata I688
> [ 0.969970] driver_register 'omap_dma_system'
> [ 0.970916] OMAP DMA hardware revision 5.0
> [ 0.973358] driver_register 'ti-dma-crossbar'
> [ 1.183898] driver_register 'omap-control-phy'
> [ 1.185394] driver_register 'pca953x'
> [ 1.186798] driver_register 'omap-dma-engine'
> [ 1.315704] omap-dma-engine 48056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
> [ 1.317352] driver_register 'edma3-tptc'
> [ 1.318420] driver_register 'edma'
> [ 1.319854] driver_register 'reg-fixed-voltage'
> [ 1.321594] _regulator_do_enable bl-enable
> [ 1.325653] driver_register 'palmas-pmic'
> [ 1.327117] driver_register 'tps65023'
> [ 1.327667] driver_register 'tps6507x-pmic'
> [ 1.328369] driver_register 'tps65910-pmic'
> [ 1.329467] driver_register 'twl_reg'
> [ 1.337768] driver_register 'omap-iommu'
> [ 1.338653] omap-iommu 480bd400.mmu: 480bd400.mmu registered
> [ 1.345062] driver_register 'tps65910'
> [ 1.345764] driver_register 'palmas'
> [ 1.348419] SCSI subsystem initialized
> [ 1.352172] libata version 3.00 loaded.
> [ 1.354492] driver_register 'Generic PHY'
> [ 1.355743] driver_register 'Generic 10G PHY'
> [ 1.357635] driver_register 'usbfs'
> [ 1.359436] usbcore: registered new interface driver usbfs
> [ 1.359497] driver_register 'hub'
> [ 1.360870] usbcore: registered new interface driver hub
> [ 1.361114] driver_register 'usb'
> [ 1.361602] usbcore: registered new device driver usb
> [ 1.361633] driver_register 'usb_phy_generic'
> [ 1.367218] driver_register 'omap_i2c'
> [ 1.375701] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz
> [ 1.381072] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz
> [ 1.385833] omap_i2c 48060000.i2c: bus 2 rev4.4 at 100 kHz
> [ 1.391204] Advanced Linux Sound Architecture Driver Initialized.
> [ 1.414886] clocksource: Switched to clocksource 32k_counter
> [ 1.626403] VFS: Disk quotas dquot_6.6.0
> [ 1.626678] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> [ 1.749755] driver_register 'usbhs_tll'
> [ 1.754638] NET: Registered protocol family 2
> [ 1.759429] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
> [ 1.759582] TCP bind hash table entries: 4096 (order: 5, 147456 bytes)
> [ 1.761840] TCP: Hash tables configured (established 4096 bind 4096)
> [ 1.762176] UDP hash table entries: 256 (order: 2, 20480 bytes)
> [ 1.762512] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
> [ 1.764801] NET: Registered protocol family 1
> [ 1.766052] driver_register 'usbhs_omap'
> [ 1.776977] driver_register 'armv7-pmu'
> [ 1.777832] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
> [ 1.779418] driver_register 'omap_timer'
> [ 1.789886] driver_register 'alarmtimer'
> [ 1.797760] futex hash table entries: 256 (order: 2, 16384 bytes)
> [ 1.819335] workingset: timestamp_bits=30 max_order=17 bucket_order=0
> [ 1.822052] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 1.836059] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
> [ 1.836273] io scheduler noop registered
> [ 1.836303] io scheduler deadline registered
> [ 1.836425] io scheduler cfq registered (default)
> [ 1.836791] driver_register 'omap-ocp2scp'
> [ 1.837799] driver_register 'omap-usb2'
> [ 1.838684] driver_register 'ti-pipe3'
> [ 1.839508] driver_register 'pinctrl-single'
> [ 1.842895] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030 size 568
> [ 1.843841] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size 92
> [ 1.849182] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size 92
> [ 1.850067] driver_register 'twl-pwm'
> [ 1.851226] driver_register 'twl-pwmled'
> [ 1.852294] driver_register 'platform-lcd'
> [ 1.854064] driver_register 'of_fixed_factor_clk'
> [ 1.856475] driver_register 'of_fixed_clk'
> [ 1.857971] driver_register 'gpio-clk'
> [ 1.859069] driver_register 'palmas-clk'
> [ 1.860504] driver_register 'twl6040-pdmclk'
> [ 1.861267] driver_register 'dra7-atl'
> [ 1.862976] driver_register 'pbias-regulator'
> [ 1.867889] driver_register 'ti_abb'
> [ 1.869110] _regulator_do_enable abb_mpu_iva
> [ 1.873443] driver_register 'omap_uart'
> [ 1.874176] DTR_gpio -2 inverted 0
> [ 1.874206] DTR_gpio -22 inverted 0
> [ 1.874237] omap_uart 4806a000.serial: no wakeirq for uart0
> [ 1.877838] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP UART0
> [ 1.883239] DTR_gpio -2 inverted 0
> [ 1.883270] DTR_gpio -22 inverted 0
> [ 1.883697] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP UART2
> [ 2.616546] random: fast init done
> [ 2.951354] console [ttyO2] enabled
> [ 2.958129] DTR_gpio -2 inverted 0
> [ 2.961730] DTR_gpio -22 inverted 0
> [ 2.966033] omap_uart 49042000.serial: no wakeirq for uart3
> [ 2.972595] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP UART3
> [ 2.986938] driver_register 'omap_rng'
> [ 2.993469] driver_register 'omap3-rom-rng'
> [ 3.257202] brd: module loaded
> [ 3.397430] loop: module loaded
> [ 3.400756] driver_register 'twl'
> [ 3.447875] twl 0-0048: PIH (irq 23) chaining IRQs 305..313
> [ 3.454376] twl 0-0048: power (irq 310) chaining IRQs 313..320
> [ 3.474121] _regulator_do_enable exp_vdd
> [ 3.485870] _regulator_do_enable usb_1v8
> [ 3.507598] _regulator_do_enable VDD1
> [ 3.522064] _regulator_do_enable VIO
> [ 3.532806] _regulator_do_enable VINTANA1
> [ 3.542785] _regulator_do_enable VINTANA2
> [ 3.553192] _regulator_do_enable VINTDIG
> [ 3.588348] _regulator_do_enable VPLL1
> [ 3.629150] driver_register 'twl4030_power'
> [ 3.705749] driver_register 'twl4030-audio'
> [ 3.713806] driver_register 'twl6040'
> [ 3.719879] driver_register 'sd'
> [ 3.724792] driver_register 'ahci'
> [ 3.732360] driver_register 'omap2-nand'
> [ 3.739318] driver_register 'omap-elm'
> [ 3.746032] driver_register 'omap2-onenand'
> [ 3.751800] driver_register 'spidev'
> [ 3.757354] driver_register 'spi_gpio'
> [ 3.771820] driver_register 'omap2_mcspi'
> [ 3.791503] driver_register 'Atheros 8035 ethernet'
> [ 3.798217] driver_register 'Atheros 8030 ethernet'
> [ 3.804565] driver_register 'Atheros 8031 ethernet'
> [ 3.813018] libphy: Fixed MDIO Bus: probed
> [ 3.818969] driver_register 'SMSC LAN83C185'
> [ 3.824066] driver_register 'SMSC LAN8187'
> [ 3.829498] driver_register 'SMSC LAN8700'
> [ 3.835266] driver_register 'SMSC LAN911x Internal PHY'
> [ 3.841308] driver_register 'SMSC LAN8710/LAN8720'
> [ 3.847808] driver_register 'SMSC LAN8740'
> [ 3.853240] driver_register 'ks8851'
> [ 3.857788] driver_register 'ks8851_mll'
> [ 3.863952] driver_register 'smc91x'
> [ 3.869323] driver_register 'smsc911x'
> [ 3.875946] driver_register 'davinci_mdio'
> [ 3.881622] driver_register 'cpsw-phy-sel'
> [ 3.888031] driver_register 'cpsw'
> [ 3.893737] driver_register 'am335x-control-usb'
> [ 3.900115] driver_register 'am335x-phy-driver'
> [ 3.908996] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 3.917572] driver_register 'usb-storage'
> [ 3.922576] usbcore: registered new interface driver usb-storage
> [ 3.932983] mousedev: PS/2 mouse device common for all mice
> [ 3.939910] driver_register 'atkbd'
> [ 3.946777] driver_register 'omap_rtc'
> [ 3.953338] driver_register 'palmas-rtc'
> [ 3.959106] i2c /dev entries driver
> [ 3.970214] Driver for 1-wire Dallas network protocol.
> [ 3.977874] driver_register 'w1_master_driver'
> [ 3.983734] driver_register 'w1_slave_driver'
> [ 3.989105] driver_register 'am335x-bandgap'
> [ 3.995971] driver_register 'ti-soc-thermal'
> [ 4.001464] ti-soc-thermal 48002524.bandgap: This OMAP thermal sensor is unreliable. You've been warned
> [ 4.012054] ti-soc-thermal 48002524.bandgap: Non-trimmed BGAP, Temp not accurate
> [ 4.027099] driver_register 'omap_wdt'
> [ 4.038421] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
> [ 4.048095] driver_register 'twl4030_wdt'
> [ 4.056671] driver_register 'cpufreq-dt'
> [ 4.073730] driver_register 'omap-cpufreq'
> [ 4.080322] driver_register 'pwrseq_simple'
> [ 4.089843] driver_register 'pwrseq_emmc'
> [ 4.096008] driver_register 'mmcblk'
> [ 4.100250] driver_register 'sdio_uart'
> [ 4.105438] driver_register 'mmci-omap'
> [ 4.110534] driver_register 'omap_hsmmc'
> [ 4.119384] regulator_enable VMMC1
> [ 4.123260] regulator_disable VMMC1
> [ 4.127380] _regulator_do_disable VMMC1
> [ 4.132232] regulator_enable pbias_mmc_omap2430
> [ 4.137176] regulator_disable pbias_mmc_omap2430
> [ 4.141998] _regulator_do_disable pbias_mmc_omap2430
> [ 4.149780] regulator_enable VMMC1
> [ 4.154022] _regulator_do_enable VMMC1
> [ 4.159179] regulator_enable VSIM
> [ 4.162963] _regulator_do_enable VSIM
> [ 4.167785] regulator_enable pbias_mmc_omap2430
> [ 4.172515] _regulator_do_enable pbias_mmc_omap2430
> [ 4.240844] ledtrig-cpu: registered to indicate activity on CPUs
> [ 4.248504] driver_register 'hid-generic'
> [ 4.254821] driver_register 'usbhid'
> [ 4.262054] usbcore: registered new interface driver usbhid
> [ 4.268402] usbhid: USB HID core driver
> [ 4.272796] driver_register 'palmas-usb'
> [ 4.279296] driver_register 'bmp280'
> [ 4.284088] driver_register 'bmp280'
> [ 4.289642] driver_register 'st-press-i2c'
> [ 4.295257] driver_register 'st-press-spi'
> [ 4.304168] driver_register 'snd-soc-dummy'
> [ 4.310943] driver_register 'soc-audio'
> [ 4.316650] driver_register 'oprofile-perf'
> [ 4.323272] oprofile: using arm/armv7
> [ 4.328552] Initializing XFRM netlink socket
> [ 4.333221] NET: Registered protocol family 17
> [ 4.338714] NET: Registered protocol family 15
> [ 4.343872] Key type dns_resolver registered
> [ 4.350677] omap2_set_init_voltage: unable to find boot up OPP for vdd_core
> [ 4.358245] omap2_set_init_voltage: unable to set vdd_core
> [ 4.370208] mmc0: host does not support reading read-only switch, assuming write-enable
> [ 4.379180] ThumbEE CPU extension supported.
> [ 4.379241] Registering SWP/SWPB emulation handler
> [ 4.379241] SmartReflex Class3 initialized
> [ 4.427368] mmc0: new high speed SDHC card at address b368
> [ 4.465301] mmcblk0: mmc0:b368 USD 7.46 GiB
> [ 4.476257] mmcblk0: p1 p2
> [ 4.524688] UBI error: cannot open mtd 4, error -19[ 4.531127] driver_register 'gpio-keys'
> [ 4.538146] input: gpio_keys as /devices/platform/gpio_keys/input/input0
> [ 4.554565] input: gpio-keys at 1 as /devices/platform/gpio-keys at 1/input/input1
> [ 4.569488] hctosys: unable to open rtc device (rtc0)
> [ 4.574829] sr_init: No PMIC hook to init smartreflex
> [ 4.581207] driver_register 'smartreflex'
> [ 4.586242] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
> [ 4.598266] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
> [ 4.612945] VAUX3: disabling
> [ 4.616638] _regulator_do_disable VAUX3
> [ 4.621734] VDAC: disabling
> [ 4.624694] _regulator_do_disable VDAC
> [ 4.630340] VUSB3V1: disabling
> [ 4.633544] _regulator_do_disable VUSB3V1
> [ 4.638580] VPLL2: disabling
> [ 4.641601] _regulator_do_disable VPLL2
> [ 4.646270] ALSA device list:
> [ 4.649383] No soundcards found.
> [ 4.706420] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
> [ 4.715209] VFS: Mounted root (ext4 filesystem) on device 179:2.
> [ 4.733673] devtmpfs: mounted
> [ 4.740386] Freeing unused kernel memory: 1024K (c0b00000 - c0c00000)
> Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory
> INIT: version 2.88 booting
> [info] Using makefile-style concurrent boot in runlevel S.
> [....] Starting the hotplug events dispatcher: udevd[ 6.621948] systemd-udevd[961]: starting version 215
> ^[[c.
> [....] Synthesizing the initial hotplug events...[ ok [ 7.814727] driver_register 'omapdss'
> done.
> ^[[c[ 7.921874] driver_register 'omapdss_dss'
> [....] Waiting for /dev to be fully populated...[ 7.968261] driver_register 'omapdss_dispc'
> [ 7.995361] driver_register 'omapdss_dsi'
> [ 8.000549] driver_register 'omapdss_dpi'
> [ 8.035705] driver_register 'omapdss_sdi'
> [ 8.040405] driver_register 'omapdss_venc'
> [ 8.076416] 48050000.dss supply vdda_video not found, using dummy regulator
> [ 8.084747] OMAP DSS rev 2.0
> [ 8.141052] omapdss_dss 48050000.dss: bound 48050400.dispc (ops dispc_component_ops [omapdss])
> [ 8.201599] ehci-omap: OMAP-EHCI Host Controller driver
> [ 8.201629] driver_register 'ehci-omap'
> [ 8.202697] devm_usb_get_phy_by_phandle(..., phys, 0)
> [ 8.202728] devm_usb_get_phy_by_phandle(..., phys, 1)
> [ 8.202789] devm_usb_get_phy_by_node(ddc4fc10 48064800.ehci, df9edcd8 hsusb2_phy, (null))
> [ 8.203124] phy = fffffdfb
> [ 8.203155] ehci-omap 48064800.ehci: Can't get PHY device for port 1: -517
> [ 8.328124] driver_register 'twl4030_keypad'
> [ 8.329071] twl4030_keypad 48070000.i2c:twl at 48:keypad: OF: linux,keymap property not defined in /ocp at 68000000/i2c at 48070000/twl at 48/keypad
> [ 8.329101] twl4030_keypad 48070000.i2c:twl at 48:keypad: Failed to build keymap
> [ 8.329162] twl4030_keypad: probe of 48070000.i2c:twl at 48:keypad failed with error -2
> [ 8.334045] driver_register 'twl4030_bci'
> [ 8.349365] driver_register 'twl4030_madc'
> [ 8.361724] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, ddff6e20)
> [ 8.361755] phy = fffffdfb
> [ 8.387634] driver_register 'twl4030_pwrbutton'
> [ 8.396881] twl4030_madc 48070000.i2c:twl at 48:madc: clk disabled, enabling
> [ 8.406982] 48070000.i2c:twl at 48:madc supply vusb3v1 not found, using dummy regulator
> [ 8.407318] regulator_enable regulator-dummy
> [ 8.430603] iio_device_register_inputbridge()
> [ 8.430603] iio_device_register_inputbridge(): 0 0 (null) ADCIN0 0
> [ 8.430633] iio_device_register_inputbridge(): 1 1 (null) ADCIN1 9
> [ 8.430633] iio_device_register_inputbridge(): 2 2 (null) ADCIN2 0
> [ 8.430633] iio_device_register_inputbridge(): 3 3 (null) ADCIN3 0
> [ 8.430633] iio_device_register_inputbridge(): 4 4 (null) ADCIN4 0
> [ 8.430664] iio_device_register_inputbridge(): 5 5 (null) ADCIN5 0
> [ 8.430664] iio_device_register_inputbridge(): 6 6 (null) ADCIN6 0
> [ 8.430664] iio_device_register_inputbridge(): 7 7 (null) ADCIN7 0
> [ 8.430664] iio_device_register_inputbridge(): 8 8 (null) ADCIN8 0
> [ 8.430694] iio_device_register_inputbridge(): 9 9 (null) ADCIN9 0
> [ 8.430694] iio_device_register_inputbridge(): 10 10 (null) ADCIN10 1
> [ 8.430694] iio_device_register_inputbridge(): 11 11 (null) ADCIN11 0
> [ 8.430694] iio_device_register_inputbridge(): 12 12 (null) ADCIN12 0
> [ 8.430694] iio_device_register_inputbridge(): 13 13 (null) ADCIN13 0
> [ 8.430725] iio_device_register_inputbridge(): 14 14 (null) ADCIN14 0
> [ 8.430725] iio_device_register_inputbridge(): 15 15 (null) ADCIN15 0
> [ 8.437774] devm_usb_get_phy_by_phandle(..., phys, 0)
> [ 8.437774] devm_usb_get_phy_by_phandle(..., phys, 1)
> [ 8.437927] devm_usb_get_phy_by_node(ddc4fc10 48064800.ehci, df9edcd8 hsusb2_phy, (null))
> [ 8.438018] phy = fffffdfb
> [ 8.438018] ehci-omap 48064800.ehci: Can't get PHY device for port 1: -517
> [ 8.441741] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, ddff6520)
> [ 8.441772] phy = fffffdfb
> [ 8.448699] input: twl4030_pwrbutton as /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl at 48:pwrbutton/input/input3
> [ 8.451721] driver_register 'twl4030-codec'
> [ 8.456726] devm_usb_get_phy_by_phandle(..., phys, 0)
> [ 8.456726] devm_usb_get_phy_by_phandle(..., phys, 1)
> [ 8.456787] devm_usb_get_phy_by_node(ddc4fc10 48064800.ehci, df9edcd8 hsusb2_phy, (null))
> [ 8.456787] phy = fffffdfb
> [ 8.456817] ehci-omap 48064800.ehci: Can't get PHY device for port 1: -517
> [ 8.457733] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, dde59120)
> [ 8.457733] phy = fffffdfb
> [ 8.469848] devm_usb_get_phy_by_phandle(..., phys, 0)
> [ 8.469848] devm_usb_get_phy_by_phandle(..., phys, 1)
> [ 8.469909] devm_usb_get_phy_by_node(ddc4fc10 48064800.ehci, df9edcd8 hsusb2_phy, (null))
> [ 8.469940] phy = fffffdfb
> [ 8.469940] ehci-omap 48064800.ehci: Can't get PHY device for port 1: -517
> [ 8.470886] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, ddff6620)
> [ 8.470886] phy = fffffdfb
> [ 8.669525] driver_register 'twl_rtc'
> [ 8.679199] driver_register 'twl4030_gpio'
> [ 8.680236] twl_rtc 48070000.i2c:twl at 48:rtc: Power up reset detected.
> [ 8.680480] twl_rtc 48070000.i2c:twl at 48:rtc: Enabling TWL-RTC
> [ 8.723937] twl_rtc 48070000.i2c:twl at 48:rtc: rtc core: registered 48070000.i2c:twl at 48 as rtc0
> [ 8.732116] devm_usb_get_phy_by_phandle(..., phys, 0)
> [ 8.732147] devm_usb_get_phy_by_phandle(..., phys, 1)
> [ 8.732177] devm_usb_get_phy_by_node(ddc4fc10 48064800.ehci, df9edcd8 hsusb2_phy, (null))
> [ 8.732208] phy = fffffdfb
> [ 8.732238] ehci-omap 48064800.ehci: Can't get PHY device for port 1: -517
> [ 8.733154] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, ddff6720)
> [ 8.733184] phy = fffffdfb
> [ 8.733703] twl4030_gpio twl4030-gpio: can't dispatch IRQs from modules
> [ 8.748199] usb_add_phy_dev nop-xceiv
> [ 8.750213] devm_usb_get_phy_by_phandle(..., phys, 0)
> [ 8.750213] devm_usb_get_phy_by_phandle(..., phys, 1)
> [ 8.750274] devm_usb_get_phy_by_node(ddc4fc10 48064800.ehci, df9edcd8 hsusb2_phy, (null))
> [ 8.750305] hsusb2_phy : hsusb2_phy
> [ 8.750305] phy = ddf9a790
> [ 8.750366] regulator_enable hsusb2_vbus
> [ 8.750366] _regulator_do_enable hsusb2_vbus
> [ 8.816406] driver_register 'leds-tca6507'
> [ 8.855194] devm_usb_get_phy_by_phandle(..., phys, 2)
> [ 8.855377] ehci-omap 48064800.ehci: EHCI Host Controller
> [ 8.859344] ehci-omap 48064800.ehci: new USB bus registered, assigned bus number 1
> [ 8.860717] ehci-omap 48064800.ehci: irq 93, io mem 0x48064800
> [ 8.881622] driver_register 'tsc2007'
> [ 8.885253] ehci-omap 48064800.ehci: USB 2.0 started, EHCI 1.00
> [ 8.888702] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 8.888702] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 8.888732] usb usb1: Product: EHCI Host Controller
> [ 8.888732] usb usb1: Manufacturer: Linux 4.9.0-letux+ ehci_hcd
> [ 8.888732] usb usb1: SerialNumber: 48064800.ehci
> [ 8.900115] hub 1-0:1.0: USB hub found
> [ 8.903015] input: TSC2007 Touchscreen as /devices/platform/68000000.ocp/48072000.i2c/i2c-1/1-0048/input/input4
> [ 8.903778] hub 1-0:1.0: 3 ports detected
> [ 8.918609] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, ddff6520)
> [ 8.918609] twl4030-usb : hsusb2_phy
> [ 8.918640] phy = fffffdfb
> [ 8.925598] iio_device_register_inputbridge()
> [ 8.925598] iio_device_register_inputbridge(): 0 0 (null) x 0
> [ 8.925628] iio_device_register_inputbridge(): 1 1 (null) y 0
> [ 8.925628] iio_device_register_inputbridge(): 2 2 (null) z1 0
> [ 8.925628] iio_device_register_inputbridge(): 3 3 (null) z2 0
> [ 8.925628] iio_device_register_inputbridge(): 4 4 (null) adc 0
> [ 8.925659] iio_device_register_inputbridge(): 5 5 (null) rt 0
> [ 8.925659] iio_device_register_inputbridge(): 6 6 (null) pen 17
> [ 8.925659] iio_device_register_inputbridge(): 7 7 (null) temp0 9
> [ 8.925659] iio_device_register_inputbridge(): 8 8 (null) temp1 9
> [ 8.926696] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, ddff6e20)
> [ 8.926727] twl4030-usb : hsusb2_phy
> [ 8.926727] phy = fffffdfb
> [ 8.940582] musb_hdrc: unknown parameter 'preserve_vbus' ignored
> [ 8.942749] driver_register 'musb-hdrc'
> [ 8.989135] driver_register 'omap_hdq'
> [ 9.028137] omap_hdq 480b2000.1w: OMAP HDQ Hardware Rev 0.5. Driver in Interrupt mode
> [ 9.030883] driver_register 'twl4030_usb'
> [ 9.088928] driver_register 'musb-omap2430'
> [ 9.098663] media: Linux media interface: v0.10
> [ 9.107666] usb_add_phy_dev twl4030
> [ 9.113952] regulator_enable VUSB3V1
> [ 9.126068] _regulator_do_enable VUSB3V1
> [ 9.130340] regulator_enable VUSB1V8
> [ 9.132415] _regulator_do_enable VUSB1V8
> [ 9.146392] regulator_enable VUSB1V5
> [ 9.148742] _regulator_do_enable VUSB1V5
> [ 9.239196] devm_usb_get_phy_by_node(dddb4010 48070000.i2c:twl at 48:bci, df9e1958 twl4030-usb, ddff6520)
> [ 9.239227] twl4030-usb : hsusb2_phy
> [ 9.239227] twl4030-usb : twl4030-usb
> [ 9.239227] phy = ddf80c10
> [ 9.244445] twl4030_usb 48070000.i2c:twl at 48:twl4030-usb: Initialized TWL4030 USB module
> [ 9.275238] usb 1-2: new high-speed USB device number 2 using ehci-omap
> [ 9.291381] call_modprobe w1-family-0x01
> [ 9.304229] devm_usb_get_phy_by_phandle(..., usb-phy, 0)
> [ 9.304290] devm_usb_get_phy_by_node(ddac1c10 480ab000.usb_otg_hs, df9e1958 twl4030-usb, (null))
> [ 9.304290] twl4030-usb : hsusb2_phy
> [ 9.304321] twl4030-usb : twl4030-usb
> [ 9.304321] phy = ddf80c10
> [ 9.304321] xceiv = ddf80c10
> [ 9.304321] phy = ddf88000
> [ 9.318817] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver
> [ 9.377288] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 2
> [ 9.395385] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
> [ 9.395416] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 9.395416] usb usb2: Product: MUSB HDRC host driver
> [ 9.395446] usb usb2: Manufacturer: Linux 4.9.0-letux+ musb-hcd
> [ 9.395446] usb usb2: SerialNumber: musb-hdrc.0.auto
> [ 9.456817] hub 2-0:1.0: USB hub found
> [ 9.471282] usb 1-2: New USB device found, idVendor=0424, idProduct=9514
> [ 9.471313] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> [ 9.480255] hub 1-2:1.0: USB hub found
> [ 9.483306] hub 1-2:1.0: 5 ports detected
> [ 9.510223] hub 2-0:1.0: 1 port detected
> [ 9.563018] driver_register 'omap-mcbsp'
> [ 9.573303] Linux video capture interface: v2.00
> [ 9.613952] omap-mcbsp 49022000.mcbsp: Cannot get pinctrl: -19
> [ 9.815246] usb 1-2.1: new high-speed USB device number 3 using ehci-omap
> [ 9.966278] usb 1-2.1: New USB device found, idVendor=0424, idProduct=ec00
> [ 9.966308] usb 1-2.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
> [ 10.472869] driver_register 'leds-gpio'
> [ 10.506072] driver_register 'extcon-gpio'
> [ 10.512542] driver_register 'pwm-backlight'
> [ 10.538635] driver_register 'twl4030_madc_hwmon'
> [ 10.539550] extcon-gpio: probe of antenna-detect failed with error -22
> [ 10.541290] pinctrl-single 48002030.pinmux: pin 48002176.0 already requested by 48002030.pinmux; cannot claim for backlight
> [ 10.541320] pinctrl-single 48002030.pinmux: pin-163 (backlight) status -22
> [ 10.541320] pinctrl-single 48002030.pinmux: could not request pin 163 (48002176.0) from group backlight_pins_pimnux on device pinctrl-single
> [ 10.541351] pwm-backlight backlight: Error applying setting, reverse things back
> [ 10.541503] pwm-backlight: probe of backlight failed with error -22
> [ 10.557983] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
> [ 10.681945] UBIFS error (pid: 1013): cannot open "ubi0:gta04-rootfs", error -19
> [ 10.681945] driver_register 'omap3isp'
> [ 10.682647] OF: graph: no port node found in /ocp at 68000000/isp at 480bc000/ports
> [ 10.682769] 480bc000.isp supply vdd-csiphy1 not found, using dummy regulator
> [ 10.683197] 480bc000.isp supply vdd-csiphy2 not found, using dummy regulator
> [ 10.683715] omap3isp 480bc000.isp: Revision 15.0 found
> [ 10.782714] iommu: Adding device 480bc000.isp to group 0
> [ 10.783416] omap-iommu 480bd400.mmu: 480bd400.mmu: version 1.1
> [ 10.784515] omap3isp 480bc000.isp: hist: using DMA channel dma0chan2
> [ 10.784576] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CCP2 was not initialized!
> [ 10.788970] driver_register 'omap-twl4030'
> [ 10.790222] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 10.790252] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> [ 10.856628] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CSI2a was not initialized!
> [ 10.866271] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP CCDC was not initialized!
> [ 10.867309] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP preview was not initialized!
> [ 10.874816] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP resizer was not initialized!
> [ 10.877746] driver_register 'w2sg0004'
> [ 10.878662] w2sg_probe()
> [ 10.878875] w2sg_probe() lna_regulator = ffffffed
> [ 10.878906] w2sg0004 w2sg0004: failed to get uart phandle in /w2sg0004 node
> [ 10.941345] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP AEWB was not initialized!
> [ 10.941375] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP AF was not initialized!
> [ 10.941406] omap3isp 480bc000.isp: Entity type for entity OMAP3 ISP histogram was not initialized!
> [ 10.969146] w2sg_rfkill_set_block: blocked: 0
> [ 10.969146] w2sg_set_lna_power: off
> [ 10.969970] w2sg0004 probed
> [ 10.969970] w2sg power gpio ON
> [ 11.009735] omap3isp 480bc000.isp: OMAP3 ISP AEWB: all buffers were freed.
> [ 11.009735] omap3isp 480bc000.isp: OMAP3 ISP AF: all buffers were freed.
> [ 11.009826] omap3isp 480bc000.isp: OMAP3 ISP histogram: all buffers were freed.
> [ 11.010375] iommu: Removing device 480bc000.isp from group 0
> [ 11.011169] clk_unregister: unregistering prepared clock: cam_xclka
> [ 11.011566] clk_unregister: unregistering prepared clock: cam_xclkb
> [ 11.012756] omap3isp: probe of 480bc000.isp failed with error -22
> [ 11.230895] UBIFS error (pid: 1014): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.506195] UBIFS error (pid: 1015): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.507354] UBIFS error (pid: 1016): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.509643] UBIFS error (pid: 1017): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.551452] UBIFS error (pid: 1018): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.552856] UBIFS error (pid: 1020): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.747711] UBIFS error (pid: 1019): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.747711] w2sg power gpio OFF
> [ 11.796539] UBIFS error (pid: 1021): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.848297] UBIFS error (pid: 1022): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.928497] UBIFS error (pid: 1023): cannot open "ubi0:gta04-rootfs", error -19
> [ 11.956329] UBIFS error (pid: 1024): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.077575] UBIFS error (pid: 1025): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.077575] regulator_disable VUSB1V5
> [ 12.077667] _regulator_do_disable VUSB1V5
> [ 12.078613] regulator_disable VUSB1V8
> [ 12.078643] _regulator_do_disable VUSB1V8
> [ 12.079071] regulator_disable VUSB3V1
> [ 12.079101] _regulator_do_disable VUSB3V1
> [ 12.175781] UBIFS error (pid: 1026): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.238586] UBIFS error (pid: 1027): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.245330] UBIFS error (pid: 1028): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.276367] UBIFS error (pid: 1029): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.456237] UBIFS error (pid: 1030): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.534790] UBIFS error (pid: 1031): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.555755] UBIFS error (pid: 1033): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.579956] UBIFS error (pid: 1032): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.596099] UBIFS error (pid: 1034): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.762908] UBIFS error (pid: 1035): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.853302] UBIFS error (pid: 1036): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.858612] UBIFS error (pid: 1037): cannot open "ubi0:gta04-rootfs", error -19
> [ 12.915985] UBIFS error (pid: 1038): cannot open "ubi0:gta04-rootfs", error -19
> [ 13.990631] UBIFS error (pid: 1039): cannot open "ubi0:gta04-rootfs", error -19
> [ 13.990661] driver_register 'bq27000-battery'
> [ 13.993713] bq27000-battery bq27000-battery: support ver. 1.2.0 enabled
> [ 14.055358] w2sg_set_power to 1 (0)
> [ 14.055725] w2sg scheduled for 1
> [ 14.057037] w2sg_set_lna_power: on
> [ 14.057098] w2sg: power gpio ON
> [ 14.074645] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 14.074676] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> [ 14.076690] w2sg: power gpio OFF
> [ 14.095275] w2sg: idle
> [ 14.401306] driver_register 'smsc95xx'
> [ 14.401641] smsc95xx v1.0.5
> [ 14.408355] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 14.408386] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> [ 14.600006] smsc95xx 1-2.1:1.0 eth0: register 'smsc95xx' at usb-48064800.ehci-2.1, smsc95xx USB 2.0 Ethernet, 6e:82:28:49:a3:12
> [ 14.603302] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 14.603332] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> [ 14.608062] usbcore: registered new interface driver smsc95xx
> [ 15.412170] omapdss_dss 48050000.dss: bound 48050c00.encoder (ops venc_component_ops [omapdss])
> [ 15.423858] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 15.433776] driver_register 'omapdss_hdmi'
> [ 15.437530] driver_register 'omapdss_hdmi5'
> [ 15.455322] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> [ 15.676147] driver_register 'connector-analog-tv'
> [ 15.690246] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 15.705200] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> [ 15.720092] driver_register 'panel-tpo-td028ttec1'
> [ 15.732635] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 15.745819] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> [ 16.558288] [drm] Initialized
> [ 17.466857] driver_register 'dmm'
> [ 17.475280] driver_register 'omapdrm'
> [ 17.480926] 48050000.dss supply vdds_dsi not found, using dummy regulator
> [ 17.503143] omapdrm omapdrm.0: DMM not available, disable DMM support
> [ 17.523590] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
> [ 17.530853] [drm] No driver support for vblank timestamp query.
> [ 17.570404] regulator_enable regulator-dummy
> [ 17.641448] Console: switching to colour frame buffer device 60x40
> [ 17.670501] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
> [ 17.712005] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
> [ 17.721313] omap-twl4030 sound: ASoC: CPU DAI (null) not registered
> [ 17.737335] omap-twl4030 sound: devm_snd_soc_register_card() failed: -517
> done.
> ^[[c[....] Warning: fstab entry for /dev/shm; should probably be for /run/shm unless working around a bug in the Oracle database ...^[[c (warning).
> [....] Activating swap...done.
> ^[[c[ 20.133972] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
> [....] Checking root file system...fsck from util-linux 2.25.2
> [ 20.498779] random: crng init done
> rootfs: clean, 88054/408000 files, 831028/1629640 blocks
> done.
> [ 20.881347] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
> ^[[c[....] Activating lvm and md swap...done.
> ^[[c[....] Checking file systems...fsck from util-linux 2.25.2
> done.
> ^[[c[....] Cleaning up temporary files... /tmp. ok
> ^[[c[ 24.006317] UBIFS error (pid: 1500): cannot open "ubi0:gta04-rootfs", error -19[....] Mounting local filesystems...mount: special device /dev/mmcblk1p1 does not exist
> mount: unknown filesystem type 'ubifs'
> failed.
> [....] Activating swapfile swap...done.
> [....] Warning: fstab entry for /dev/shm; should probably be for /run/shm unless working around a bug in the Oracle database ... (warning).
> ^[[c^[[c^[[c[....] Cleaning up temporary files.... ok
> ^[[c[....] Setting kernel variables ...done.
> ^[[c[....] Configuring network interfaces...[ 38.596954] smsc95xx 1-2.1:1.0 eth0: hardware isn't capable of remote wakeup
> [ 39.838806] call_modprobe usbfunc:ecm
> [ 39.879333] using random self ethernet address
> [ 39.884002] using random host ethernet address
> [ 39.907135] usb0: HOST MAC 9a:65:0c:1a:fa:0d
> [ 39.920837] usb0: MAC 52:10:f4:f4:68:9f
> [ 39.935272] using random self ethernet address
> [ 39.939941] using random host ethernet address
> [ 39.956817] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
> [ 39.963775] g_ether gadget: g_ether ready
> done.
> ^[[c[....] Cleaning up temporary files.... ok
> ^[[c[....] Setting up ALSA...warning: 'alsactl -E HOME=/var/run/alsa restore' failed with error message 'alsactl: load_state:1729: No soundcards found...'...done.
> ^[[c[....] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix^[[c.
> INIT: Entering runlevel: 2
> [info] Using makefile-style concurrent boot in runlevel 2.
> [....] Starting enhanced syslogd: rsyslogd. ok
> ^[[c[....] Starting automount.... ok
> [ 44.378936] call_modprobe net-pf-16-proto-9
> ^[[c[....] Starting system message bus: dbus. ok
> ^[[c[ 44.939880] call_modprobe net-pf-31
> [ 45.242645] Bluetooth: Core ver 2.22
> [ 45.258209] NET: Registered protocol family 31
> [ 45.262908] Bluetooth: HCI device and connection manager initialized
> [ 45.285797] Bluetooth: HCI socket layer initialized
> [ 45.290954] Bluetooth: L2CAP socket layer initialized
> [ 45.307617] Bluetooth: SCO socket layer initialized
> [ 45.357574] call_modprobe bt-proto-4
> [ 45.410461] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
> [ 45.425201] Bluetooth: BNEP socket layer initialized
> [....] Starting bluetooth: bluetoothd. ok
> ^[[c[....] Starting periodic command scheduler: cron. ok
> ^[[c[ 46.292663] call_modprobe net-pf-10
> [ 46.783447] NET: Registered protocol family 10
> [ 46.820251] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> [ 46.835815] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
> [....] Loading cpufreq kernel modules...done (none).
> ^[[c[....] CPUFreq Utilities: Setting ondemand CPUFreq governor...CPU0...done.
> ^[[c[....] Starting NTP server: ntpd. ok
> ^[[c[....] Starting OpenBSD Secure Shell server: sshd. ok
> ^[[c
>
> X.Org X Server 1.16.4
> Release Date: 2014-12-20
> X Protocol Version 11, Revision 0
> Build Operating System: Linux 3.16.0-0.bpo.4-armmp-lpae armv7l Debian
> Current Operating System: Linux gta04 4.9.0-letux+ #518 SMP PREEMPT Mon Dec 12 21:06:05 CET 2016 armv7l
> Kernel command line: console=ttyO2,115200n8 mtdoops.mtddev=omap2.nand ubi.mtd=4 root=/dev/mmcblk0p2 rw rootfstype=ext4,ext3 rootwait console=ttyO2,115200n8 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk
> Build Date: 11 February 2015 01:18:06AM
> xorg-server 2:1.16.4-1 (http://www.debian.org/support)
> Current version of pixman: 0.32.6
> Before reporting problems, check http://wiki.x.org
> to make sure that you have the latest version.
> Markers: (--) probed, (**) from config file, (==) default setting,
> (++) from command line, (!!) notice, (II) informational,
> (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
> (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan 1 00:00:40 2000
> (==) Using config file: "/etc/X11/xorg.conf"
> (==) Using system config directory "/usr/share/X11/xorg.conf.d"
>
> Debian GNU/Linux 8 gta04 ttyO2
>
> gta04 login: root
> Password:
> [ 52.947937] call_modprobe net-pf-16-proto-9
> [ 52.980133] call_modprobe net-pf-16-proto-9
> Last login: Sat Jan 1 00:00:46 UTC 2000 on ttyO2
> Linux gta04 4.9.0-letux+ #518 SMP PREEMPT Mon Dec 12 21:06:05 CET 2016 armv7l
>
> The programs included with the Debian GNU/Linux system are free software;
> the exact distribution terms for each program are described in the
> individual files [ 53.125335] call_modprobe net-pf-16-proto-9
> in /usr/share/doc/*/copyright.
>
> Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
> permitted by applicable law.
> [ 53.180023] call_modprobe net-pf-16-proto-9
> [ 53.221191] call_modprobe net-pf-16-proto-9
> root at gta04:~# export TERM="xterm-color" COLUMNS=119 LINES=67
> root at gta04:~# uname -a
> Linux gta04 4.9.0-letux+ #518 SMP PREEMPT Mon Dec 12 21:06:05 CET 2016 armv7l GNU/Linux
> rroot at gta04:~# cpufreq-info
> cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009
> Report errors and bugs to cpufreq at vger.kernel.org, please.
> analyzing CPU 0:
> driver: cpufreq-dt
> CPUs which run at the same hardware frequency: 0
> CPUs which need to have their frequency coordinated by software: 0
> maximum transition latency: 300 us.
> hardware limits: 300 MHz - 800 MHz
> available frequency steps: 300 MHz, 600 MHz, 800 MHz
> available cpufreq governors: conservative, userspace, powersave, ondemand, performance
> current policy: frequency should be within 300 MHz and 800 MHz.
> The governor "ondemand" may decide which speed to use
> within this range.
> current CPU frequency is 300 MHz (asserted by call to hardware).
> cpufreq stats: 300 MHz:82.51%, 600 MHz:5.91%, 800 MHz:11.58% (28)
> root at gta04:~#
> _______________________________________________
> http://projects.goldelico.com/p/gta04-kernel/
> Letux-kernel mailing list
> Letux-kernel at openphoenux.org
> http://lists.goldelico.com/mailman/listinfo.cgi/letux-kernel
More information about the Letux-kernel
mailing list