[Gta04-owner] GTA04A5 - Success!

Moritz Schilling moritz.k.schilling at gmail.com
Wed May 11 13:08:48 CEST 2016


Wow, congrats!!! This is amazing :)

On Wed, May 11, 2016 at 1:03 PM, H. Nikolaus Schaller <hns at goldelico.com>
wrote:

> Hi,
>
> > Am 08.05.2016 um 00:12 schrieb B <wankelwankel at yahoo.com>:
> >
> > On May 7, 2016 5:10:57 PM CEST, "H. Nikolaus Schaller" <
> hns at goldelico.com> wrote:
> >> Hi,
> >> I finally managed in the haven't-counted attempt to solder a working
> >> DM3730 SoC plus the new Samsung PoP RAM/NAND chip on an old GTA04A4
> >> board.>
> >> Please expect more test results in the next days. And a final "go" for
> >> the GTA04A5 production run.
> >
> >>
> >
> >
> > That brings a smile, congratulations!
>
> Well,
> trying to make the board boot to Linux did lead to a big sad :(
>
> Initially.
>
> The reason was that the RAM did not respond properly. It did store
> something, but not all patterns.
>
> After some hours of experimentation to make it work, I took the PCB under
> the microscope and found
> by biggest magnification and looking on the gap between the DM3730
> processor and the memory
> chip that not all BGA balls of the memory chip were soldered properly.
>
> But before unsoldering everything and redoing from scratch I pressed a
> little solder flux into the
> gap and did run it again through our vapour phase reflow oven.
>
> And voila, the DM3730 still boots. No new short circuits under the chip.
> And now it even finds the RAM!
> Attached is a boot log where you can see that there is indeed 1GB RAM on
> this GTA04.
>
> Now we have the real :)
>
> I have not tested the OneNAND side of the chip (there are driver problems
> in our old MLO/U-Boot
> and it takes too much time to adapt to a newer version just for these
> tests).
>
> But even if NAND makes problems the GTA04 can still be operated from µSD.
>
> This means we will place the order for the GTA04A5 production asap :) :) :)
>
> BR,
> Nikolaus
>
>
> > --
> > Sent from my OpenPhoenux GTA04, with only one key still working. It
> explains why my mail lacks elaboration, spelling or grammar at points.
>
> Well, with one key you can still do morse code to write almost everything
> (at least 50% of ASCII :).
>
> Here is the boot log:
>
>
> tذb$U   @D  tذb$U   @D  @tذb$U   @D  @
>
> Texas Instruments X-Loader (MLO) 1.4.4ss modified for GTA04 (May 11 2016 -
> 11:52:00)
> Detected Samsung KCE00E00CA A506
> OMAP3630/3730-GP ES2.1
> Board detected: GTA04A4
> SYSBOOT[5:0]: 0x10/16
> GMPC Memory: 3
> SDRC Memory: SAMSUNG MCP 512MB/bank
> Reading FAT boot sector
> Loading u-boot.bin (296352 bytes) from mmc/sd
>
>
> U-Boot 2011.03-rc1-00392-gf73f2e8 (Oct 25 2015 - 22:20:04)
>
> OMAP3630/3730-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 800 Mhz
> GTA04 + LPDDR/NAND
> I2C:   ready
> DRAM:  1 GiB
> NAND:  0 MiB
> MMC:   OMAP SD/MMC: 0
> *** Warning - readenv() failed, using default environment
>
> In:    serial
> Out:   serial
> Err:   serial
> Device Tree: omap3-gta04a4
> Die ID #634c00029ff80000015a8b0507012009
> Hit any key to stop autoboot:  0
> reading boot.scr
> 14649 bytes read in 6 ms (2.3 MiB/s)
> Running bootscript from mmc ...
> ## Executing script at 82000000
> *** if you boot from NAND don-t worry about error messages when U-Boot
> tries to read a non-existing MMC ***
> Setting bus to 0
> did init LED driver for TCA6507
> *** initializing GTA04 environment ***
>
> no devices available
> can not flash - must always boot from SD card
> *** initializing LCM ***
> board_video_init() for JBT6K74-AS / TD028TTEC1
> did backlight_init() on GPIO_57
> did panel_reg_init()
> dss panel config
> dss enable
> did board_video_init()
> did jbt_init_regs()
> lcm backlight level set to 255 (0..255)
> *** loading splash from MMC ***
> Setting bus to 0
> reading splash.rgb16
> ** Unable to read file splash.rgb16 **
> reading splash.rgb16z
> 39304 bytes read in 8 ms (4.7 MiB/s)
> Uncompressed size: 614400 = 0x96000
> *** booting Linux ***
> Setting bus to 0
> trying partitions 1 2 3 4
> reading uImage
> 4558368 bytes read in 496 ms (8.8 MiB/s)
> found kernel /uImage on partition 1
> reading bootargs.scr
> 2108 bytes read in 4 ms (514.6 KiB/s)
> ## Executing script at 80800000
> running bootargs.scr
> bootargs.scr done...
> reading omap3-gta04a4.dtb
> 72361 bytes read in 15 ms (4.6 MiB/s)
> PARTITION=1
> PARTITIONTYPE=FAT
> baudrate=115200
> boot=if itest $FDT == 1; then bootm ${loadaddr} - ${loadaddrfdt}; else
> bootm ${loadaddr}; fi;
> bootaddr=0x81800000
> bootargs=console=ttyO2,115200n8 mtdoops.mtddev=omap2.nand ubi.mtd=4
> root=/dev/mmcblk0p2 rw rootfstype=ext4,ext3 rootwait
> bootcmd=if run loadbootscript; then run bootscript; else run mmcboot; fi;
> bootdelay=1
> bootorder=1 2 3 4
> bootscript=echo Running bootscript ...; source ${bootaddr}
> console=ttyO2,115200n8
> defaultdisplay=lcd
> devicetree=omap3-gta04a4
> dieid#=634c00029ff80000015a8b0507012009
> dvimode=1024x768MR-16 at 60
> filesize=0x11aa9
> imgaddr=80400000
> imgfile=splash
> imgnandaddr=1d0000
> imgtempaddr=0x80800000
> kernelloaded=status set 10
> kernelloading=status set 18
> kernelmmc=0
> loadaddr=0x82000000
> loadaddrfdt=0x81c00000
> loadbootscript=i2c dev 0; mmc rescan ${mmc}; if load mmc ${mmc}
> ${bootaddr} boot.scr; then echo did load bootscript from mmc; elif nand
> read ${bootaddr} 250000 10000; then echo did load bootscript from nand; fi
> loadimg=i2c dev 0; mmc rescan ${mmc}; if load mmc ${mmc} ${imgaddr}
> ${imgfile}.rgb16; then; elif load mmc ${mmc} ${imgtempaddr}
> ${imgfile}.rgb16z; then unzip ${imgtempaddr} ${imgaddr}; elif nand read
> ${imgtempaddr} ${imgnandaddr} 40000; then unzip ${imgtempaddr} ${imgaddr};
> fi
> loadkernel=run kernelloading;i2c dev 0;mmc rescan
> ${mmc};DONE=0;KERNEL=0;FDT=0;run nandargs;echo trying partitions
> $bootorder;for p in $bootorder;do;if itest $DONE == 0;then;if load mmc
> ${mmc}:${p} ${loadaddr} uImage;then;echo found kernel /uImage on partition
> $p;setenv mmcroot "/dev/mmcblk${kernelmmc}p${p} rw";run
> mmcargs;KERNEL=1;DONE=1;elif load mmc ${mmc}:${p} ${loadaddr}
> /boot/uImage;then;echo found kernel /boot/uImage on EXT partition $p;setenv
> mmcroot "/dev/mmcblk${kernelmmc}p${p} rw";run mmcargs;KERNEL=1;DONE=1;fi;if
> load mmc ${mmc}:${p} ${imgtempaddr} bootargs.scr;then;setenv PARTITION
> $p;setenv PARTITIONTYPE FAT;source ${imgtempaddr};DONE=1;elif load mmc
> ${mmc}:${p} ${imgtempaddr} /boot/bootargs.scr;then;setenv PARTITION
> $p;setenv PARTITIONTYPE EXT;source ${imgtempaddr};DONE=1;fi;if load mmc
> ${mmc}:${p} ${loadaddrfdt} ${devicetree}.dtb;then;FDT=1;elif load mmc
> ${mmc}:${p} ${loadaddrfdt} /boot/${devicetree}.dtb;then;FDT=1;fi;fi;done;if
> itest $KERNEL == 0;then;if nand read ${loadaddr} 280000 600000;then;echo
> fallback to NAND kernel;FDT=0;else;status blink;fi;fi;run kernelloaded
> loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage
> mmc=0
> mmcargs=setenv bootargs console=${console} mpurate=${mpurate} mux=${mux}
> vram=${vram} omapfb.vram=${omapfbvram} omapfb.mode=dvi:${dvimode}
> omapfb.debug=y omapdss.def_disp=${defaultdisplay} ubi.mtd=${nand}
> root=${mmcroot} rootfstype=${mmcrootfstype}
> mmcboot=if run loadkernel; then run boot; fi;
> mmcdev=0
> mmcroot=/dev/mmcblk0p2 rw
> mmcrootfstype=ext4,ext3 rootwait
> mpurate=800
> mux=GTA04A3+
> nand=4
> nandargs=setenv bootargs console=${console} mpurate=${mpurate} mux=${mux}
> vram=${vram} omapfb.vram=${omapfbvram} omapfb.mode=dvi:${dvimode}
> omapfb.debug=y omapdss.def_disp=${defaultdisplay} ubi.mtd=${nand}
> root=${nandroot} rootfstype=${nandrootfstype}
> nandboot=run kernelloading; if nand read ${loadaddr} 280000 600000; then
> run nandargs; run kernelloaded; bootm ${loadaddr}; fi;
> nandroot=ubi0:gta04-rootfs
> nandrootfstype=ubifs
> omapfbvram=0:8M,1:4M
> scriptversion=20151025223319
> showimg=run loadimg; lcm fb ${imgaddr};
> usbtty=cdc_acm
> vram=12M
>
> Environment size: 3459/131068 bytes
> lcm state set to deep-standby
> display power off
> ## Booting kernel from Legacy Image at 82000000 ...
>    Image Name:   Linux-4.6.0-rc7-letux+
>    Image Type:   ARM Linux Kernel Image (uncompressed)
>    Data Size:    4558304 Bytes = 4.3 MiB
>    Load Address: 80008000
>    Entry Point:  80008000
>    Verifying Checksum ... OK
> ## Flattened Device Tree blob at 81c00000
>    Booting using the fdt blob at 0x81c00000
>    Loading Kernel Image ... OK
> OK
>    Loading Device Tree to 8ffeb000, end 8ffffaa8 ... OK
>
> Starting kernel ...
>
> [    0.000000] Booting Linux on physical CPU 0x0
> [    0.000000] Linux version 4.6.0-rc7-letux+ (hns at iMac.local) (gcc
> version 4.9.2 (GCC) ) #311 SMP PREEMPT Tue May 10 14:40:27 CEST 2016
> [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
> cr=10c5387d
> [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
> instruction cache
> [    0.000000] Machine model: Goldelico GTA04A4/Letux 2804
> [    0.000000] cma: Reserved 16 MiB at 0xbe800000
> [    0.000000] Memory policy: Data cache writeback
> [    0.000000] CPU: All CPU(s) started in SVC mode.
> [    0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
> [    0.000000] percpu: Embedded 14 pages/cpu @ef795000 s25472 r8192 d23680
> u57344
> [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.
> Total pages: 260096
> [    0.000000] Kernel command line: console=ttyO2,115200n8
> mtdoops.mtddev=omap2.nand ubi.mtd=4 root=/dev/mmcblk0p2 rw
> rootfstype=ext4,ext3 rootwait
> [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
> [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288
> bytes)
> [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
> bytes)
> [    0.000000] Memory: 1001732K/1046528K available (6342K kernel code,
> 653K rwdata, 2268K rodata, 1024K init, 8016K bss, 28412K reserved, 16384K
> cma-reserved, 243712K highmem)
> [    0.000000] Virtual kernel memory layout:
> [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
> [    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
> [    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
> [    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
> [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
> [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
> [    0.000000]       .text : 0xc0008000 - 0xc0968984   (9603 kB)
> [    0.000000]       .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
> [    0.000000]       .data : 0xc0b00000 - 0xc0ba36d4   ( 654 kB)
> [    0.000000]        .bss : 0xc0ba36d4 - 0xc1377a84   (8017 kB)
> [    0.000000] Running RCU self tests
> [    0.000000] Preemptible hierarchical RCU implementation.
> [    0.000000]  RCU debugfs-based tracing is enabled.
> [    0.000000]  RCU lockdep checking is enabled.
> [    0.000000]  Build-time adjustment of leaf fanout to 32.
> [    0.000000]  RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1.
> [    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
> [    0.000000] NR_IRQS:16 nr_irqs:16 16
> [    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
> interrupts
> [    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
> [    0.000000] OMAP clockevent source: timer1 at 32768 Hz
> [    0.000000] clocksource: 32k_counter: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 58327039986419 ns
> [    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps
> every 65535999984741ns
> [    0.000030] OMAP clocksource: 32k_counter at 32768 Hz
> [    0.002227] Console: colour dummy device 80x30
> [    0.002319] Lock dependency validator: Copyright (c) 2006 Red Hat,
> Inc., Ingo Molnar
> [    0.002349] ... MAX_LOCKDEP_SUBCLASSES:  8
> [    0.002380] ... MAX_LOCK_DEPTH:          48
> [    0.002380] ... MAX_LOCKDEP_KEYS:        8191
> [    0.002410] ... CLASSHASH_SIZE:          4096
> [    0.002410] ... MAX_LOCKDEP_ENTRIES:     32768
> [    0.002441] ... MAX_LOCKDEP_CHAINS:      65536
> [    0.002441] ... CHAINHASH_SIZE:          32768
> [    0.002471]  memory used by lock dependency info: 5167 kB
> [    0.002471]  per task-struct memory footprint: 1536 bytes
> [    0.002532] Calibrating delay loop... 594.73 BogoMIPS (lpj=2973696)
> [    0.105041] pid_max: default: 32768 minimum: 301
> [    0.105621] Security Framework initialized
> [    0.105865] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
> [    0.105895] Mountpoint-cache hash table entries: 2048 (order: 1, 8192
> bytes)
> [    0.111297] CPU: Testing write buffer coherency: ok
> [    0.114288] CPU0: thread -1, cpu 0, socket -1, mpidr 0
> [    0.114471] Setting up static identity map for 0x80100000 - 0x80100058
> [    0.126403] Brought up 1 CPUs
> [    0.126464] SMP: Total of 1 processors activated (594.73 BogoMIPS).
> [    0.126464] CPU: All CPU(s) started in SVC mode.
> [    0.132629] devtmpfs: initialized
> [    0.304565] VFP support v0.3: implementor 41 architecture 3 part 30
> variant c rev 3
> [    0.307952] clocksource: jiffies: mask: 0xffffffff max_cycles:
> 0xffffffff, max_idle_ns: 19112604462750000 ns
> [    0.310699] driver_register 'ARM-CCI PMU'
> [    0.311065] driver_register 'ARM-CCI'
> [    0.311340] pinctrl core: initialized pinctrl subsystem
> [    0.314147] driver_register 'reg-dummy'
> [    0.329833] NET: Registered protocol family 16
> [    0.340942] DMA: preallocated 256 KiB pool for atomic coherent
> allocations
> [    0.470733] omap_hwmod: mcbsp2_sidetone using broken dt data from mcbsp
> [    0.474426] omap_hwmod: mcbsp3_sidetone using broken dt data from mcbsp
> [    0.627319] driver_register 'omap_gpio'
> [    0.631530] driver_register 'syscon'
> [    0.637756] driver_register 'dummy'
> [    0.638153] driver_register 'omap-gpmc'
> [    0.638397] driver_register 'omap_l3_smx'
> [    0.638641] driver_register 'omap_l3_noc'
> [    0.639434] Reprogramming SDRC clock to 332000000 Hz
> [    0.689331] OMAP GPIO hardware version 2.5
> [    0.826446] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
> [    0.826812] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
> [    0.895019] No ATAGs?
> [    0.895080] hw-breakpoint: debug architecture 0x4 unsupported.
> [    0.898223] omap4_sram_init:Unable to allocate sram needed to handle
> errata I688
> [    0.898254] omap4_sram_init:Unable to get sram pool needed to handle
> errata I688
> [    0.899719] driver_register 'omap_dma_system'
> [    0.900817] OMAP DMA hardware revision 5.0
> [    0.903137] driver_register 'ti-dma-crossbar'
> [    1.074188] driver_register 'omap-control-phy'
> [    1.076080] driver_register 'pca953x'
> [    1.077728] driver_register 'omap-dma-engine'
> [    1.120483] omap-dma-engine 48056000.dma-controller: OMAP DMA engine
> driver
> [    1.121582] driver_register 'edma3-tptc'
> [    1.122436] driver_register 'edma'
> [    1.128356] driver_register 'reg-fixed-voltage'
> [    1.129669] driver_register 'palmas-pmic'
> [    1.131713] driver_register 'tps65023'
> [    1.132019] driver_register 'tps6507x-pmic'
> [    1.132507] driver_register 'tps65910-pmic'
> [    1.136291] driver_register 'twl_reg'
> [    1.145355] driver_register 'omap-iommu'
> [    1.146392] omap-iommu 480bd400.mmu: 480bd400.mmu registered
> [    1.151947] driver_register 'tps65910'
> [    1.154907] driver_register 'palmas'
> [    1.158203] SCSI subsystem initialized
> [    1.163452] driver_register 'Generic PHY'
> [    1.164459] driver_register 'Generic 10G PHY'
> [    1.167205] driver_register 'usbfs'
> [    1.168701] usbcore: registered new interface driver usbfs
> [    1.168762] driver_register 'hub'
> [    1.170135] usbcore: registered new interface driver hub
> [    1.170379] driver_register 'usb'
> [    1.170959] usbcore: registered new device driver usb
> [    1.171020] driver_register 'usb_phy_generic'
> [    1.172668] hsusb2_phy supply vcc not found, using dummy regulator
> [    1.174713] usb_add_phy_dev nop-xceiv
> [    1.177734] driver_register 'omap_i2c'
> [    1.187103] omap_i2c 48070000.i2c: bus 0 rev4.4 at 2600 kHz
> [    1.205657] omap_i2c 48072000.i2c: bus 1 rev4.4 at 400 kHz
> [    1.209289] omap_i2c 48060000.i2c: bus 2 rev4.4 at 100 kHz
> [    1.217041] Advanced Linux Sound Architecture Driver Initialized.
> [    1.244964] clocksource: Switched to clocksource 32k_counter
> [    1.469482] VFS: Disk quotas dquot_6.6.0
> [    1.469787] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
> bytes)
> [    1.601745] driver_register 'usbhs_tll'
> [    1.608398] NET: Registered protocol family 2
> [    1.613464] TCP established hash table entries: 8192 (order: 3, 32768
> bytes)
> [    1.613739] TCP bind hash table entries: 8192 (order: 6, 294912 bytes)
> [    1.619384] TCP: Hash tables configured (established 8192 bind 8192)
> [    1.619873] UDP hash table entries: 512 (order: 3, 40960 bytes)
> [    1.620483] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
> [    1.622344] NET: Registered protocol family 1
> [    1.622497] driver_register 'usbhs_omap'
> [    1.633941] driver_register 'armv7-pmu'
> [    1.634765] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5
> counters available
> [    1.638031] driver_register 'omap_timer'
> [    1.651641] driver_register 'alarmtimer'
> [    1.660003] futex hash table entries: 256 (order: 2, 16384 bytes)
> [    1.672943] workingset: timestamp_bits=28 max_order=18 bucket_order=0
> [    1.677490] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [    1.690795] bounce: pool size: 64 pages
> [    1.692016] Block layer SCSI generic (bsg) driver version 0.4 loaded
> (major 250)
> [    1.692260] io scheduler noop registered
> [    1.692321] io scheduler deadline registered
> [    1.692382] io scheduler cfq registered (default)
> [    1.692565] driver_register 'omap-ocp2scp'
> [    1.694641] driver_register 'omap-usb2'
> [    1.697937] driver_register 'ti-pipe3'
> [    1.699829] driver_register 'pinctrl-single'
> [    1.703094] pinctrl-single 48002030.pinmux: 284 pins at pa fa002030
> size 568
> [    1.704162] pinctrl-single 48002a00.pinmux: 46 pins at pa fa002a00 size
> 92
> [    1.707916] pinctrl-single 480025a0.pinmux: 46 pins at pa fa0025a0 size
> 92
> [    1.708679] pinctrl-single 480022d8.pinmux: Invalid submask 0x40800 for
> pinmux_tv_acbias_pins at 0x0
> [    1.709167] pinctrl-single 480022d8.pinmux: 1 pins at pa fa0022d8 size 4
> [    1.710083] driver_register 'twl-pwm'
> [    1.711517] driver_register 'twl-pwmled'
> [    1.713226] driver_register 'platform-lcd'
> [    1.716278] driver_register 'pbias-regulator'
> [    1.722778] driver_register 'omap_uart'
> [    1.723815] DTR_gpio -2 inverted 0
> [    1.723846] DTR_gpio -22 inverted 0
> [    1.723907] omap_uart 4806a000.serial: no wakeirq for uart0
> [    1.727386] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 88,
> base_baud = 3000000) is a OMAP UART0
> [    1.731781] DTR_gpio -2 inverted 0
> [    1.731811] DTR_gpio -22 inverted 0
> [    1.731872] omap_uart 4806c000.serial: no wakeirq for uart1
> [    1.732666] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 89,
> base_baud = 3000000) is a OMAP UART1
> [    1.736785] DTR_gpio 21 inverted 0
> [    1.736999] DTR_gpio 21 inverted 0
> [    1.737060] omap_uart 49020000.serial: no wakeirq for uart2
> [    1.737487] 49020000.serial: ttyO2 at MMIO 0x49020000 (irq = 90,
> base_baud = 3000000) is a OMAP UART2
> [    2.719360] console [ttyO2] enabled
> [    2.726593] DTR_gpio -2 inverted 0
> [    2.730163] DTR_gpio -22 inverted 0
> [    2.733856] omap_uart 49042000.serial: no wakeirq for uart3
> [    2.741088] 49042000.serial: ttyO3 at MMIO 0x49042000 (irq = 96,
> base_baud = 3000000) is a OMAP UART3
> [    2.755859] driver_register 'omap_rng'
> [    2.762634] driver_register 'omap3-rom-rng'
> [    2.880767] brd: module loaded
> [    2.952728] loop: module loaded
> [    2.957183] driver_register 'twl'
> [    2.994201] twl 0-0048: PIH (irq 23) chaining IRQs 338..346
> [    3.001068] twl 0-0048: power (irq 343) chaining IRQs 346..353
> [    3.099365] VMMC2: failed to apply 1800000uV constraint(-22)
> [    3.111816] twl_reg 48070000.i2c:twl at 48:regulator-vmmc2: can't
> register VMMC2, -22
> [    3.120697] twl_reg: probe of 48070000.i2c:twl at 48:regulator-vmmc2
> failed with error -22
> [    3.184692] driver_register 'twl4030_power'
> [    3.220489] driver_register 'twl4030-audio'
> [    3.230438] driver_register 'twl6040'
> [    3.237609] driver_register 'sd'
> [    3.242309] driver_register 'ahci'
> [    3.250610] driver_register 'omap2-nand'
> [    3.257324] nand: No NAND device found
> [    3.261291] omap2-nand omap2-nand.0: scan failed, may be bus-width
> mismatch
> [    3.270416] driver_register 'omap-elm'
> [    3.277282] driver_register 'omap2-onenand'
> [    3.283935] driver_register 'spidev'
> [    3.289031] driver_register 'spi_gpio'
> [    3.304290] driver_register 'omap2_mcspi'
> [    3.326904] driver_register 'SMSC LAN83C185'
> [    3.332672] driver_register 'SMSC LAN8187'
> [    3.337921] driver_register 'SMSC LAN8700'
> [    3.343505] driver_register 'SMSC LAN911x Internal PHY'
> [    3.350341] driver_register 'SMSC LAN8710/LAN8720'
> [    3.356872] driver_register 'SMSC LAN8740'
> [    3.362396] driver_register 'Atheros 8035 ethernet'
> [    3.368377] driver_register 'Atheros 8030 ethernet'
> [    3.374694] driver_register 'Atheros 8031 ethernet'
> [    3.380706] driver_register 'ks8851'
> [    3.386230] driver_register 'ks8851_mll'
> [    3.391967] driver_register 'smc91x'
> [    3.398376] driver_register 'smsc911x'
> [    3.404510] driver_register 'davinci_mdio'
> [    3.411010] driver_register 'cpsw-phy-sel'
> [    3.418029] driver_register 'cpsw'
> [    3.423980] driver_register 'am335x-control-usb'
> [    3.430725] driver_register 'am335x-phy-driver'
> [    3.440155] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [    3.448822] driver_register 'usb-storage'
> [    3.453918] usbcore: registered new interface driver usb-storage
> [    3.464721] mousedev: PS/2 mouse device common for all mice
> [    3.471740] driver_register 'atkbd'
> [    3.479156] driver_register 'omap_rtc'
> [    3.486907] driver_register 'palmas-rtc'
> [    3.492675] i2c /dev entries driver
> [    3.504547] Driver for 1-wire Dallas network protocol.
> [    3.511718] driver_register 'w1_master_driver'
> [    3.518157] driver_register 'w1_slave_driver'
> [    3.523956] driver_register 'ti-soc-thermal'
> [    3.530242] ti-soc-thermal 48002524.bandgap: This OMAP thermal sensor
> is unreliable. You've been warned
> [    3.540802] ti-soc-thermal 48002524.bandgap: Non-trimmed BGAP, Temp not
> accurate
> [    3.556640] driver_register 'omap_wdt'
> [    3.568695] omap_wdt: OMAP Watchdog Timer Rev 0x31: initial timeout 60
> sec
> [    3.578369] driver_register 'twl4030_wdt'
> [    3.588043] driver_register 'cpufreq-dt'
> [    3.594390] driver_register 'omap-cpufreq'
> [    3.600494] driver_register 'mmcblk'
> [    3.606475] driver_register 'sdio_uart'
> [    3.611145] driver_register 'mmci-omap'
> [    3.617523] driver_register 'omap_hsmmc'
> [    3.674041] ledtrig-cpu: registered to indicate activity on CPUs
> [    3.681884] driver_register 'hid-generic'
> [    3.687896] driver_register 'usbhid'
> [    3.696807] usbcore: registered new interface driver usbhid
> [    3.703338] usbhid: USB HID core driver
> [    3.708221] driver_register 'gpio-clk'
> [    3.714599] driver_register 'palmas-clk'
> [    3.721954] driver_register 'twl6040-clk'
> [    3.730041] driver_register 'dra7-atl'
> [    3.736175] mmc0: host does not support reading read-only switch,
> assuming write-enable
> [    3.746368] driver_register 'palmas-usb'
> [    3.753417] driver_register 'st-press-i2c'
> [    3.758728] mmc0: new high speed SDHC card at address 59b4
> [    3.771545] driver_register 'st-press-spi'
> [    3.784423] mmcblk0: mmc0:59b4 USD   7.51 GiB
> [    3.790496] driver_register 'snd-soc-dummy'
> [    3.793029] driver_register 'soc-audio'
> [    3.798919] driver_register 'oprofile-perf'
> [    3.801391] oprofile: using arm/armv7
> [    3.803161] Initializing XFRM netlink socket
> [    3.803436] NET: Registered protocol family 17
> [    3.803833] NET: Registered protocol family 15
> [    3.804504] Key type dns_resolver registered
> [    3.815612] omap2_set_init_voltage: unable to find boot up OPP for
> vdd_mpu_iva
> [    3.815612] omap2_set_init_voltage: unable to set vdd_mpu_iva
> [    3.815673] omap2_set_init_voltage: unable to find boot up OPP for
> vdd_core
> [    3.815673] omap2_set_init_voltage: unable to set vdd_core
> [    3.843811] ThumbEE CPU extension supported.
> [    3.843872] Registering SWP/SWPB emulation handler
> [    3.886322] UBI error: cannot open mtd 4, error -19
> [    3.886322] driver_register 'gpio-keys'
> [    3.889221] input: gpio-keys as /devices/platform/gpio-keys/input/input0
> [    3.908721] input: gpio-keys-wwan-wakeup as
> /devices/platform/gpio-keys-wwan-wakeup/input/input1
> [    3.917297] hctosys: unable to open rtc device (rtc0)
> [    4.022979]  mmcblk0: p1 p2
> [    4.086853] VAUX3: disabling
> [    4.091033] VDAC: disabling
> [    4.094818] VUSB1V5: disabling
> [    4.099090] VUSB1V8: disabling
> [    4.103088] VUSB3V1: disabling
> [    4.108001] ALSA device list:
> [    4.111114]   No soundcards found.
> [    4.121368]
> [    4.122955] ===============================
> [    4.127349] [ INFO: suspicious RCU usage. ]
> [    4.131744] 4.6.0-rc7-letux+ #311 Not tainted
> [    4.136291] -------------------------------
> [    4.140686] include/trace/events/power.h:328 suspicious
> rcu_dereference_check() usage!
> [    4.148986]
> [    4.148986] other info that might help us debug this:
> [    4.148986]
> [    4.157348]
> [    4.157348] RCU used illegally from idle CPU!
> [    4.157348] rcu_scheduler_active = 1, debug_locks = 0
> [    4.168762] RCU used illegally from extended quiescent state!
> [    4.174774] no locks held by swapper/0/0.
> [    4.178955]
> [    4.178955] stack backtrace:
> [    4.183532] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc7-letux+
> #311
> [    4.190826] Hardware name: Generic OMAP36xx (Flattened Device Tree)
> [    4.197418] [<c010f198>] (unwind_backtrace) from [<c010b6d4>]
> (show_stack+0x10/0x14)
> [    4.205535] [<c010b6d4>] (show_stack) from [<c03f16fc>]
> (dump_stack+0x98/0xd0)
> [    4.213134] [<c03f16fc>] (dump_stack) from [<c012596c>]
> (pwrdm_set_next_pwrst+0x160/0x24c)
> [    4.221801] [<c012596c>] (pwrdm_set_next_pwrst) from [<c01201e0>]
> (omap_sram_idle+0x60/0x228)
> [    4.230743] [<c01201e0>] (omap_sram_idle) from [<c0120468>]
> (omap3_pm_idle+0xc0/0x264)
> [    4.239044] [<c0120468>] (omap3_pm_idle) from [<c0107ac0>]
> (arch_cpu_idle+0x18/0x3c)
> [    4.247192] [<c0107ac0>] (arch_cpu_idle) from [<c0176740>]
> (cpu_startup_entry+0x214/0x370)
> [    4.255859] [<c0176740>] (cpu_startup_entry) from [<c0a00be8>]
> (start_kernel+0x328/0x394)
> [    4.264434] [<c0a00be8>] (start_kernel) from [<8000807c>] (0x8000807c)
> [    4.426300] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data
> mode. Opts: (null)
> [    4.435089] VFS: Mounted root (ext4 filesystem) on device 179:2.
> [    4.451538] devtmpfs: mounted
> [    4.458099] Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
> Mount failed for selinuxfs on /sys/fs/selinux:  No such file or directory
> INIT: version 2.88 booting
> [info] Using makefile-style concurrent boot in runlevel S.
> [....] Starting the hotplug events dispatcher: udevd[    6.167846]
> systemd-udevd[904]: starting version 215
> [    6.252441] random: udevd urandom read with 47 bits of entropy available
> ^[[c.
> [....] Synthesizing the initial hotplug events...[    7.033905]
> driver_register 'omapdss'
> done.
> ^[[c[....] Waiting for /dev to be fully populated...[    7.143432]
> driver_register 'omapdss_dss'
> [    7.162139] ehci-omap: OMAP-EHCI Host Controller driver
> [    7.162139] driver_register 'ehci-omap'
> [    7.163146] devm_usb_get_phy_by_phandle(..., phys, 0)
> [    7.163146] devm_usb_get_phy_by_phandle(..., phys, 1)
> [    7.163238] devm_usb_get_phy_by_node(eebbe810 48064800.ehci, ef7e9bc0
> hsusb2_phy,   (null))
> [    7.163238] hsusb2_phy : hsusb2_phy
> [    7.163238] phy = eeb06a90
> [    7.179290] devm_usb_get_phy_by_phandle(..., phys, 2)
> [    7.179351] ehci-omap 48064800.ehci: EHCI Host Controller
> [    7.188446] ehci-omap 48064800.ehci: new USB bus registered, assigned
> bus number 1
> [    7.188995] ehci-omap 48064800.ehci: irq 93, io mem 0x48064800
> [    7.205230] ehci-omap 48064800.ehci: USB 2.0 started, EHCI 1.00
> [    7.205810] usb usb1: New USB device found, idVendor=1d6b,
> idProduct=0002
> [    7.205841] usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [    7.205841] usb usb1: Product: EHCI Host Controller
> [    7.205841] usb usb1: Manufacturer: Linux 4.6.0-rc7-letux+ ehci_hcd
> [    7.205841] usb usb1: SerialNumber: 48064800.ehci
> [    7.207763] hub 1-0:1.0: USB hub found
> [    7.207855] hub 1-0:1.0: 3 ports detected
> [    7.271820] driver_register 'twl4030_bci'
> [    7.272583] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76720)
> [    7.272613] twl4030-usb : hsusb2_phy
> [    7.272613] phy = fffffdfb
> [    7.278411] driver_register 'twl4030_madc'
> [    7.304077] twl4030_madc 48070000.i2c:twl at 48:madc: clk disabled,
> enabling
> [    7.304809] 48070000.i2c:twl at 48:madc supply vusb3v1 not found, using
> dummy regulator
> [    7.311676] driver_register 'twl4030_pwrbutton'
> [    7.332244] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76420)
> [    7.332275] twl4030-usb : hsusb2_phy
> [    7.332275] phy = fffffdfb
> [    7.340515] input: twl4030_pwrbutton as
> /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl at 48
> :pwrbutton/input/input2
> [    7.348541] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76320)
> [    7.348571] twl4030-usb : hsusb2_phy
> [    7.348571] phy = fffffdfb
> [    7.376464] driver_register 'twl4030-vibra'
> [    7.391479] driver_register 'twl4030-codec'
> [    7.398132] input: twl4030:vibrator as
> /devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl at 48
> :audio/twl4030-vibra/input/input3
> [    7.401092] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76720)
> [    7.401123] twl4030-usb : hsusb2_phy
> [    7.401123] phy = fffffdfb
> [    7.406799] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76420)
> [    7.406829] twl4030-usb : hsusb2_phy
> [    7.406829] phy = fffffdfb
> [    7.525299] usb 1-2: new high-speed USB device number 2 using ehci-omap
> [    7.551208] driver_register 'twl_rtc'
> [    7.562225] driver_register 'twl4030_gpio'
> [    7.572540] twl_rtc 48070000.i2c:twl at 48:rtc: Power up reset detected.
> [    7.572723] twl_rtc 48070000.i2c:twl at 48:rtc: Enabling TWL-RTC
> [    7.584228] twl_rtc 48070000.i2c:twl at 48:rtc: rtc core: registered
> 48070000.i2c:twl at 48 as rtc0
> [    7.598480] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76420)
> [    7.598510] twl4030-usb : hsusb2_phy
> [    7.598510] phy = fffffdfb
> [    7.600097] twl4030_gpio twl4030-gpio: can't dispatch IRQs from modules
> [    7.603454] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76a20)
> [    7.603454] twl4030-usb : hsusb2_phy
> [    7.603454] phy = fffffdfb
> [    7.673156] driver_register 'musb-hdrc'
> [    7.702789] usb 1-2: New USB device found, idVendor=0af0, idProduct=8800
> [    7.702789] usb 1-2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=0
> [    7.702819] usb 1-2: Product: Globetrotter HSUPA Modem
> [    7.702819] usb 1-2: Manufacturer: Option N.V.
> [    7.720764] driver_register 'leds-tca6507'
> [    7.728485] driver_register 'hmc5843'
> [    7.737976] driver_register 'tsc2007'
> [    7.749664] driver_register 'bma150'
> [    7.754730] omap_hsmmc 480b4000.mmc: allocated mmc-pwrseq
> [    7.793151] driver_register 'omap-mcbsp'
> [    7.796051] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76620)
> [    7.796081] twl4030-usb : hsusb2_phy
> [    7.796081] phy = fffffdfb
> [    7.804504] driver_register 'twl4030_usb'
> [    7.807556] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76620)
> [    7.807556] twl4030-usb : hsusb2_phy
> [    7.807556] phy = fffffdfb
> [    7.822540] driver_register 'itg3200'
> [    7.825469] input: TSC2007 Touchscreen as
> /devices/platform/68000000.ocp/48072000.i2c/i2c-1/1-0048/input/input4
> [    7.829467] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76620)
> [    7.829467] twl4030-usb : hsusb2_phy
> [    7.829467] phy = fffffdfb
> [    7.833343] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76720)
> [    7.833343] twl4030-usb : hsusb2_phy
> [    7.833374] phy = fffffdfb
> [    7.837280] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76720)
> [    7.837280] twl4030-usb : hsusb2_phy
> [    7.837280] phy = fffffdfb
> [    7.840454] driver_register 'at24'
> [    7.847198] driver_register 'bmp085'
> [    7.849822] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76620)
> [    7.849853] twl4030-usb : hsusb2_phy
> [    7.849853] phy = fffffdfb
> [    7.852569] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76a20)
> [    7.852600] twl4030-usb : hsusb2_phy
> [    7.852600] phy = fffffdfb
> [    7.858520] input: bma150 as
> /devices/platform/68000000.ocp/48072000.i2c/i2c-1/1-0041/input/input5
> [    7.864257] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76a20)
> [    7.864288] twl4030-usb : hsusb2_phy
> [    7.864288] phy = fffffdfb
> [    7.874511] usb_add_phy_dev twl4030
> [    7.886596] devm_usb_get_phy_by_node(eedc5810 48070000.i2c:twl at 48:bci,
> ef7da8a0 twl4030-usb, eef76020)
> [    7.886596] twl4030-usb : hsusb2_phy
> [    7.886596] twl4030-usb : twl4030-usb
> [    7.886627] phy = ed8afc10
> [    7.886657] twl4030_bci 48070000.i2c:twl at 48:bci: could not request vac
> iio channel
> [    7.889892] at24 1-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
> [    7.894195] bmp085 1-0077: Successfully initialized bmp085!
> [    7.913543] twl4030_usb 48070000.i2c:twl at 48:twl4030-usb: Initialized
> TWL4030 USB module
> [    7.953399] driver_register 'omap_hdq'
> [    7.962005] driver_register 'musb-omap2430'
> [    7.970886] omap_hdq 480b2000.1w: OMAP HDQ Hardware Rev 0.5. Driver in
> Interrupt mode
> [    7.996978] devm_usb_get_phy_by_phandle(..., usb-phy, 0)
> [    7.997039] devm_usb_get_phy_by_node(eea1a810 480ab000.usb_otg_hs,
> ef7da8a0 twl4030-usb,   (null))
> [    7.997039] twl4030-usb : hsusb2_phy
> [    7.997039] twl4030-usb : twl4030-usb
> [    7.997070] phy = ed8afc10
> [    7.997070] xceiv = ed8afc10
> [    7.997070] phy = ed8b1400
> [    8.013671] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver
> [    8.015533] musb-hdrc musb-hdrc.0.auto: new USB bus registered,
> assigned bus number 2
> [    8.023193] usb usb2: New USB device found, idVendor=1d6b,
> idProduct=0002
> [    8.023193] usb usb2: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [    8.023223] usb usb2: Product: MUSB HDRC host driver
> [    8.023223] usb usb2: Manufacturer: Linux 4.6.0-rc7-letux+ musb-hcd
> [    8.023223] usb usb2: SerialNumber: musb-hdrc.0.auto
> [    8.036590] hub 2-0:1.0: USB hub found
> [    8.037078] hub 2-0:1.0: 1 port detected
> [    8.049835] media: Linux media interface: v0.10
> [    8.326507] Linux video capture interface: v2.00
> [    8.514587] driver_register 'extcon-gpio'
> [    8.530242] extcon-gpio: probe of antenna-detect failed with error -22
> [    8.553344] driver_register 'pwm-backlight'
> [    8.554077] backlight supply power not found, using dummy regulator
> [    8.597229] driver_register 'twl4030_madc_battery'
> [    8.643524] driver_register 'omap-dmtimer-pwm'
> [    8.647308] backlight supply power not found, using dummy regulator
> [    8.677062] backlight supply power not found, using dummy regulator
> [    8.752441] wwan_on_off_init
> [    8.752441] driver_register 'wwan-on-off'
> [    8.753112] wwan_on_off_probe()
> [    8.753295] devm_usb_get_phy_by_phandle(..., usb-port, 0)
> [    8.753356] devm_usb_get_phy_by_node(eea4a410 modem, ef7e9bc0
> hsusb2_phy,   (null))
> [    8.753387] hsusb2_phy : hsusb2_phy
> [    8.753387] phy = eeb06a90
> [    8.753387] onoff = 186 indicator = -2 act low: 0 usb_phy = -290428272
> [    8.753387] wwan_on_off_probe() pdata=eded7ed0
> [    8.755706] USB phy event 0
> [    8.756072] wwan_on_off_rfkill_set_block: blocked: 1
> [    8.756072] modem: set_power 0
> [    8.756072] USB phy event 0
> [    8.756103]   state 0
> [    8.756103] modem: done
> [    8.756103] wwan-on-off successfully probed
> [    8.768493] wwan_on_off_probe()
> [    8.768524] devm_usb_get_phy_by_phandle(..., usb-port, 0)
> [    8.768524] onoff = -2 indicator = -2 act low: 0 usb_phy = -19
> [    8.768554] wwan_on_off_probe() pdata=eded7450
> [    8.768554] wwan-on-off: I have no control over modem
> [    8.768615] gpio gpiochip9: Detected name collision for GPIO name
> 'gpio-wwan-enable'
> [    8.786224] wwan_on_off_rfkill_set_block: blocked: 0
> [    8.786224] modem: set_power 1
> [    8.786224] USB phy event 0
> [    8.786224]   state 0
> [    8.786224] modem: send impulse
> [    8.790222] driver_register 'omap3isp'
> [    8.790924] omap3isp 480bc000.isp: parsing endpoint /ocp/isp at 480bc000
> /ports/port at 0/endpoint, interface 0
> [    8.791137] ERROR: Bad of_node_put() on /ocp/isp at 480bc000/ports/port at 0
> /endpoint
> [    8.791168] CPU: 0 PID: 927 Comm: udevd Not tainted 4.6.0-rc7-letux+
> #311
> [    8.791168] Hardware name: Generic OMAP36xx (Flattened Device Tree)
> [    8.791198] [<c010f198>] (unwind_backtrace) from [<c010b6d4>]
> (show_stack+0x10/0x14)
> [    8.791229] [<c010b6d4>] (show_stack) from [<c03f16fc>]
> (dump_stack+0x98/0xd0)
> [    8.791229] [<c03f16fc>] (dump_stack) from [<c03f3764>]
> (kobject_release+0x60/0x74)
> [    8.791259] [<c03f3764>] (kobject_release) from [<c05a1c28>]
> (__of_get_next_child+0x40/0x48)
> [    8.791290] [<c05a1c28>] (__of_get_next_child) from [<c05a1c58>]
> (of_get_next_child+0x28/0x44)
> [    8.791290] [<c05a1c58>] (of_get_next_child) from [<c05a1e50>]
> (of_graph_get_next_endpoint+0xe4/0x124)
> [    8.791412] [<c05a1e50>] (of_graph_get_next_endpoint) from [<bf207898>]
> (isp_probe+0xd8/0xd90 [omap3_isp])
> [    8.791503] [<bf207898>] (isp_probe [omap3_isp]) from [<c047be3c>]
> (platform_drv_probe+0x50/0xa0)
> [    8.791534] [<c047be3c>] (platform_drv_probe) from [<c0479f1c>]
> (driver_probe_device+0x134/0x29c)
> [    8.791534] [<c0479f1c>] (driver_probe_device) from [<c047a10c>]
> (__driver_attach+0x88/0xac)
> [    8.791564] [<c047a10c>] (__driver_attach) from [<c04785ec>]
> (bus_for_each_dev+0x6c/0x90)
> [    8.791564] [<c04785ec>] (bus_for_each_dev) from [<c04795cc>]
> (bus_add_driver+0xcc/0x1e8)
> [    8.791564] [<c04795cc>] (bus_add_driver) from [<c047b05c>]
> (driver_register+0xac/0xf4)
> [    8.791595] [<c047b05c>] (driver_register) from [<c01018e0>]
> (do_one_initcall+0x100/0x1b8)
> [    8.791625] [<c01018e0>] (do_one_initcall) from [<c0209508>]
> (do_init_module+0x58/0x398)
> [    8.791625] [<c0209508>] (do_init_module) from [<c01c69f8>]
> (load_module+0x18b4/0x19d4)
> [    8.791656] [<c01c69f8>] (load_module) from [<c01c6ce8>]
> (SyS_finit_module+0x88/0x90)
> [    8.791656] [<c01c6ce8>] (SyS_finit_module) from [<c0107020>]
> (ret_fast_syscall+0x0/0x1c)
> [    8.791717] omap3isp 480bc000.isp: parsing endpoint /ocp/isp at 480bc000
> /ports/port at 1/endpoint, interface 1
> [    8.791717] omap3isp 480bc000.isp: clock lane polarity 0, pos 0
> [    8.791748] omap3isp 480bc000.isp: data lane 0 polarity 0, pos 0
> [    8.791748] omap3isp 480bc000.isp: data lane 1 polarity 0, pos 0
> [    8.791748] omap3isp 480bc000.isp: bad remote port parent
> [    8.791809] omap3isp: probe of 480bc000.isp failed with error -22
> [    8.806549] driver_register 'twl4030_madc_hwmon'
> [    8.848754] driver_register 'omap-twl4030'
> [    8.897521] driver_register 'asoc-simple-card'
> [    8.995941] usb 1-2: USB disconnect, device number 2
> [    9.505126] USB phy event 0
> [    9.505126] modem: done
> [    9.505249] wwan_on_off_rfkill_set_block: blocked: 0
> [    9.505249] wwan-on-off successfully probed
> [    9.585937] driver_register 'w2cbw003'
> [    9.595611] twl4030_voice_set_tristate codec=eef1e800 1
> [    9.596008] TPS Voice IF is tristated
> [    9.596374] twl4030-codec twl4030-codec: ASoC: no sink widget found for
> Voice DigiInput
> [    9.596374] twl4030-codec twl4030-codec: ASoC: Failed to add route
> GSMIN -> direct -> Voice DigiInput
> [    9.596405] twl4030-codec twl4030-codec: ASoC: no sink widget found for
> Voice DigiOutput
> [    9.596405] twl4030-codec twl4030-codec: ASoC: Failed to add route
> GSMOUT -> direct -> Voice DigiOutput
> [    9.596527] twl4030-codec twl4030-codec: ASoC: no source widget found
> for Voice DigiInput
> [    9.596557] twl4030-codec twl4030-codec: ASoC: Failed to add route
> Voice DigiInput -> direct -> Digital Voice Playback Mixer
> [    9.605834] omap-twl4030 sound: twl4030-hifi <-> 49022000.mcbsp mapping
> ok
> [    9.672027] driver_register 'w2sg0004'
> [    9.672637] w2sg_probe()
> [    9.673065] w2sg_probe() lna_regulator = ed51da00
> [    9.675933] w2sg_rfkill_set_block: blocked: 0
> [    9.675933] w2sg_set_lna_power: off
> [    9.675964] w2sg0004 probed
> [    9.675994] w2sg power gpio ON
> [   10.223785] 00!w2sg power gpio OFF
> [   11.008483] hso: drivers/net/usb/hso.c: Option Wireless
> [   11.008514] driver_register 'hso'
> [   11.008758] usbcore: registered new interface driver hso
> [   11.585388] driver_register 'bq27000-battery'
> [   11.609466] bq27000-battery bq27000-battery: support ver. 1.2.0 enabled
> [   11.615142] random: nonblocking pool is initialized
> [   11.992767] w2sg_set_power to 0 (0)
> [   12.414733] driver_register 'omapdss_dispc'
> [   12.431396] driver_register 'omapdss_dsi'
> [   12.439117] driver_register 'omapdss_dpi'
> [   12.446166] driver_register 'omapdss_sdi'
> [   12.452697] driver_register 'omapdss_venc'
> [   12.458343] 48050000.dss supply vdda_video not found, using dummy
> regulator
> [   12.466247] omapdss_register_output() name =dpi.0
> [   12.471282] OMAP DSS rev 2.0
> [   12.475128] omapdss_dss 48050000.dss: bound 48050400.dispc (ops
> dispc_component_ops [omapdss])
> [   12.484558] omapdss_register_output() name =venc.0
> [   12.489990] omapdss_dss 48050000.dss: bound 48050c00.encoder (ops
> venc_component_ops [omapdss])
> [   12.504821] driver_register 'omapdss_hdmi'
> [   12.512237] driver_register 'omapdss_hdmi5'
> [   12.556793] driver_register 'panel-tpo-td028ttec1'
> [   12.564086] driver_register 'amplifier-opa362'
> [   12.567504] driver_register 'connector-analog-tv'
> [   12.568969] omapdss_register_output() name =(null)
> [   12.572662] omapdss_register_display()
> [   12.572692] omapdss_register_display() name =tv
> [   12.621490] omapdss_register_display()
> [   12.625610] omapdss_register_display() name =lcd
> [   12.920227] [drm] Initialized drm 1.1.0 20060810
> [   13.254730] driver_register 'dmm'
> [   13.262176] driver_register 'omapdrm'
> [   13.266815] dsi: omap_connect_dssdevs
> [   13.270690] dsi: omap_connect_dssdevs: tv
> [   13.275634] dsi: dss_mgr_connect() 1 venc.0
> [   13.280029] dsi: omap_connect_dssdevs: lcd
> [   13.285186] dsi: dss_mgr_connect() 0 dpi.0
> [   13.289489] dsi: omap_connect_dssdevs done !no_displays
> [   13.299041] omapdrm omapdrm.0: DMM not available, disable DMM support
> [   13.312042] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
> [   13.319274] [drm] No driver support for vblank timestamp query.
> [   13.325927] [CONNECTOR:25:Unknown-1]
> [   13.329681] dsi: omap_connector_get_modes tvdsi:
> copy_timings_omap_to_drm
> [   13.337097] dsi: omap_connector_mode_valid()
> [   13.341552] dsi: omap_connector_mode_valid check_timings()
> [   13.347534] [CONNECTOR:25:Unknown-1] probed modes :
> [   13.352661] Modeline 33:"720x574i" 50 13500 720 732 796 864 574 579 584
> 625 0x48 0x1a
> [   13.360900] [CONNECTOR:29:Unknown-2]
> [   13.364654] dsi: omap_connector_get_modes lcddsi:
> copy_timings_omap_to_drm
> [   13.371948] dsi: omap_connector_mode_valid()
> [   13.376464] dsi: omap_connector_mode_valid check_timings()
> [   13.382263] [CONNECTOR:29:Unknown-2] probed modes :
> [   13.387451] Modeline 34:"480x640" 66 22153 480 504 512 520 640 644 646
> 648 0x48 0xa
> [   13.401062] omapdrm omapdrm.0: fb0: omapdrm frame buffer device
> [   13.435241] [drm] Initialized omapdrm 1.0.0 20110917 on minor 0
> [   16.616851] 24!w2sg has sent data although it should be off!
> [   16.623199] w2sg_set_lna_power: off
> [   16.627197] w2sg: power gpio ON
> [   16.635131] w2sg: power gpio OFF
> [   18.667541] w2sg_set_lna_power: off
> [   18.671295] w2sg: power gpio ON
> [   18.675628] w2sg: power gpio OFF
> [   22.689910] w2sg_set_lna_power: off
> [   22.693603] w2sg: power gpio ON
> [   22.705078] w2sg: power gpio OFF
> [   23.656311] [CONNECTOR:25:Unknown-1]
> [   23.661926] dsi: omap_connector_get_modes tv2 dsi:
> copy_timings_omap_to_drm
> [   23.671569] Modeline 33:"720x574i" 0 13500 720 732 796 864 574 579 584
> 625 0x48 0x1a
> [   23.681182] [CONNECTOR:29:Unknown-2]
> [   23.687164] dsi: omap_connector_get_modes lcd2c dsi:
> copy_timings_omap_to_drm
> [   23.698181] dsi: omap_connector_mode_valid()
> [   23.703887] dsi: omap_connector_mode_valid check_timings()
> [   23.711486] [CONNECTOR:29:Unknown-2] probed modes :
> [   23.718902] Modeline 34:"480x640" 66 22153 480 504 512 520 640 644 646
> 648 0x48 0xa
> [   23.728637] dsi: omap_plane_atomic_update vid1, crtc=eef5f800
> fb=eef1c800 dsi: omap_plane_atomic_update 480x640 -> 480x640 (480)dsi:
> omap_plane_atomic_update 0,0 0xbe900000 0x0000000033 dsi: dispc_ovl_setup()
> 1, pa 0xbe900000, pa_uv 0x00000000, sw 480, 0,0, 480x640 -> 480x640, cmode
> 80, rot 0, mir 0, chan 0 repl 0
> [   23.754791] dsi: dispc_ovl_setup_common() rotation type 1 paddr be900000
> [   23.780975] dsi: dispc_ovl_setup_common() offset0 0, offset1 0, row_inc
> 1, pix_inc 1
> [   23.790771] dsi: omap_crtc_atomic_flush() tv
> [   23.795684] dsi: omap_crtc_atomic_flush() lcd
> [   23.800323] dsi: omap_crtc_enable() lcd
> [   23.804412] dsi: omap_encoder_update()
> [   23.808502] dsi: omap_encoder_update check_timings()
> [   23.813842] dsi: omap_encoder_enable()
> [   23.820007] dsi: dss_mgr_enable()
> [   24.788757] done.
> ^[[c[....] Warning: fstab entry for /dev/shm; should probably be for
> /run/shm unless working around a bug in the Oracle database ...^[[c
> (warning).
> [   25.779998] [....] Activating swap...done.
> ^[[c
> [   28.705932] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
> [   28.776031] [....] Checking root file system...fsck from util-linux
> 2.25.2
> rootfs: clean, 37202/468640 files, 296078/1871408 blocks
> done.
> ^[[c
> [   29.572265] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
> [....] Creating compatibility symlink from /etc/mtab to /proc/mounts. ...
> [   30.895263] w2sg: idle
> [....] Activating lvm and md swap...done.
> ^[[c[....] Checking file systems...fsck from util-linux 2.25.2
> done.
> ^[[cUBIFS error (pid: 1433): cannot open "ubi0:gta04-rootfs", error -19
> [   33.789916] [....] Mounting local filesystems...mount: special device
> /dev/mmcblk1p1 does not exist
> mount: unknown filesystem type 'ubifs'
> failed.
> [....] Activating swapfile swap...done.
> [....] Warning: fstab entry for /dev/shm; should probably be for /run/shm
> unless working around a bug in the Oracle database ... (warning).
> ^[[c^[[c^[[c[....] Cleaning up temporary files.... ok
> ^[[c[....] Setting kernel variables ...done.
> [....] Configuring network interfaces...
>
> [   46.462982] NET: Registered protocol family 10
> [   49.032623] using random self ethernet address
> [   49.038635] using random host ethernet address
> [   49.051696] usb0: HOST MAC 72:08:12:43:c6:48
> [   49.085449] usb0: MAC b2:4c:a7:4e:0e:ab
> [   49.089599] using random self ethernet address
> [   49.094299] using random host ethernet address
> [   49.104736] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
> [   49.125518] g_ether gadget: g_ether ready
> [   49.200164] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
> Internet Systems Consortium DHCP Client 4.3.1
> Copyright 2004-2014 Internet Systems Consortium.
> All rights reserved.
> For info, please visit https://www.isc.org/software/dhcp/
>
> Cannot find device "eth0"
> Bind socket to interface: No such device
>
> If you think you have received this message due to a bug rather
> than a configuration issue please read the section on submitting
> bugs on either our web page at www.isc.org or in the README file
> before submitting a bug.  These pages explain the proper
> process and the information we find helpful for debugging..
>
> exiting.
> Failed to bring up eth0.
> Cannot find device "eth1"
> Failed to bring up eth1.
> done.
> [....] Cleaning up temporary files.... ok
> ^[[c
> [....] Setting up X socket directories... /tmp/.X11-unix
> /tmp/.ICE-unix^[[c.
> INIT: Entering runlevel: 2
> [info] Using makefile-style concurrent boot in runlevel 2.
>
> [....] Starting enhanced syslogd: rsyslogd. ok
> [....] Starting automount.... ok
> [....] Starting periodic command scheduler: cron. ok
> [....] Starting system message bus: dbus. ok
> [   55.460144] Bluetooth: Core ver 2.21
> [   55.471801] NET: Registered protocol family 31
> [   55.485260] Bluetooth: HCI device and connection manager initialized
> [   55.492004] Bluetooth: HCI socket layer initialized
> [   55.507110] Bluetooth: L2CAP socket layer initialized
> [   55.512603] Bluetooth: SCO socket layer initialized
> [....] Starting bluetooth: bluetoothd. ok
> [....] Loading cpufreq kernel modules...done (none).
> [....] CPUFreq Utilities: Setting ondemand CPUFreq governor...CPU0...done.
> [....] Starting NTP server: ntpd. ok
> [....] Starting OpenBSD Secure Shell server: sshd. ok
>
> xauth:  file //.Xauthority does not exist
>
>
> X.Org X Server 1.16.4
> Release Date: 2014-12-20
> X Protocol Version 11, Revision 0
> Build Operating System: Linux 3.16.0-0.bpo.4-armmp-lpae armv7l Debian
> Current Operating System: Linux letux 4.6.0-rc7-letux+ #311 SMP PREEMPT
> Tue May 10 14:40:27 CEST 2016 armv7l
> Kernel command line: console=ttyO2,115200n8 mtdoops.mtddev=omap2.nand
> ubi.mtd=4 root=/dev/mmcblk0p2 rw rootfstype=ext4,ext3 rootwait
> Build Date: 11 February 2015  01:18:06AM
> xorg-server 2:1.16.4-1 (http://www.debian.org/support)
> Current version of pixman: 0.32.6
>         Before reporting problems, check http://wiki.x.org
>         to make sure that you have the latest version.
> Markers: (--) probed, (**) from config file, (==) default setting,
>         (++) from command line, (!!) notice, (II) informational,
>         (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
> (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan  1 00:00:50 2000
> (==) Using config file: "/etc/X11/xorg.conf"
> (==) Using system config directory "/usr/share/X11/xorg.conf.d"
>
> [   58.357910] dsi: omap_plane_atomic_update vid1, crtc=eef5f800
> fb=eef1c800dsi: omap_plane_atomic_update 480x640 -> 480x640 (480)dsi:
> omap_plane_atomic_update 0,0 0xbe900000 0x00000000dsi: dispc_ovl_setup() 1,
> pa 0xbe900000, pa_uv 0x00000000, sw 480, 0,0, 480x640 -> 480x640, cmode 80,
> rot 0, mir 0, chan 0 repl 0
> [   58.388732] dsi: dispc_ovl_setup_common() rotation type 1 paddr be900000
> [   58.396850] dsi: dispc_ovl_setup_common() offset0 0, offset1 0, row_inc
> 1, pix_inc 1
> [   58.405792] dsi: omap_crtc_atomic_flush() tv
> [   58.410278] dsi: omap_crtc_atomic_flush() lcd
>
> Debian GNU/Linux 8 letux ttyO2
>
> [   58.628601] dsi: omap_plane_atomic_update vid1, crtc=eef5f800
> fb=eef1c800letux login: dsi: omap_plane_atomic_update 480x640 -> 480x640
> (480)
> dsi: omap_plane_atomic_update 0,0 0xbe900000 0x0000000033!
> [   58.674407] dsi: dispc_ovl_setup() 1, pa 0xbe900000, pa_uv 0x00000000,
> sw 480, 0,0, 480x640 -> 480x640, cmode 80, rot 0, mir 0, chan 0 repl 0
> [   58.700866] dsi: dispc_ovl_setup_common() rotation type 1 paddr be900000
> [   58.717163] dsi: dispc_ovl_setup_common() offset0 0, offset1 0, row_inc
> 1, pix_inc 1
> [   58.733489] dsi: omap_crtc_atomic_flush() tv
> [   58.740264] dsi: omap_crtc_atomic_flush() lcd
> [   58.754302] dsi: omap_plane_atomic_update vid1, crtc=eef5f800
> fb=eef1c8002c!2c!2c!2c!2c!dsi: omap_plane_atomic_update 480x640 -> 480x640
> (480)31!33!30!38!30!36!dsi: omap_plane_atomic_update 0,0 0xbe900000
> 0x000000002c!2c!2c!4e!2a!34!dsi: dispc_ovl_setup() 1, pa 0xbe900000, pa_uv
> 0x00000000, sw 480, 0,0, 480x640 -> 480x640, cmode 80, rot 0, mir 0, chan 0
> repl 0
> [   58.792663] dsi: dispc_ovl_setup_common() rotation type 1 paddr be900000
> [   58.801513] dsi: dispc_ovl_setup_common() offset0 0, offset1 0, row_inc
> 1, pix_inc 1
> [   58.810424] dsi: omap_crtc_atomic_flush() tv
> [   58.815582] dsi: omap_crtc_atomic_flush() lcd
> [   58.826599] dsi: omap_plane_atomic_update vid1, crtc=eef5f800
> fb=eef1c800dsi: omap_plane_atomic_update 480x640 -> 480x640 (480)dsi:
> omap_plane_atomic_update 0,0 0xbe900000 0x00000000dsi: dispc_ovl_setup() 1,
> pa 0xbe900000, pa_uv 0x00000000, sw 480, 0,0, 480x640 -> 480x640, cmode 80,
> rot 0, mir 0, chan 0 repl 0
> [   58.855895] dsi: dispc_ovl_setup_common() rotation type 1 paddr be900000
> [   58.862915] dsi: dispc_ovl_setup_common() offset0 0, offset1 0, row_inc
> 1, pix_inc 1
> [   58.872161] dsi: omap_crtc_atomic_flush() tv
> [   58.877532] dsi: omap_crtc_atomic_flush() lcd
> [   58.887939] [CONNECTOR:25:Unknown-1]
> [   58.891723] dsi: omap_connector_get_modes tvdsi:
> copy_timings_omap_to_drm
> [   58.899993] dsi: omap_connector_mode_valid()
> [   58.904479] dsi: omap_connector_mode_valid check_timings()
> [   58.911407] [CONNECTOR:25:Unknown-1] probed modes :
> [   58.917266] Modeline 37:"720x574i" 50 13500 720 732 796 864 574 579 584
> 625 0x48 0x1a
> [   58.926879] [CONNECTOR:29:Unknown-2]
> [   58.930633] dsi: omap_connector_get_modes lcddsi:
> copy_timings_omap_to_drm
> [   58.939178] dsi: omap_connector_mode_valid()
> [   58.943634] dsi: omap_connector_mode_valid check_timings()
> [   58.950378] [CONNECTOR:29:Unknown-2] probed modes :
> [   58.956329] Modeline 34:"480x640" 66 22153 480 504 512 520 640 644 646
> 648 0x48 0xa
> [   58.964843] [CONNECTOR:25:Unknown-1]
> [   58.969543] dsi: omap_connector_get_modes tvdsi:
> copy_timings_omap_to_drm
> [   58.977447] dsi: omap_connector_mode_valid()
> [   58.981933] dsi: omap_connector_mode_valid check_timings()
> [   58.988464] [CONNECTOR:25:Unknown-1] probed modes :
> [   58.993591] Modeline 37:"720x574i" 50 13500 720 732 796 864 574 579 584
> 625 0x48 0x1a
> [   59.003417] [CONNECTOR:29:Unknown-2]
> [   59.009246] dsi: omap_connector_get_modes lcddsi:
> copy_timings_omap_to_drm
> [   59.017242] dsi: omap_connector_mode_valid()
> [   59.021728] dsi: omap_connector_mode_valid check_timings()
> [   59.028228] [CONNECTOR:29:Unknown-2] probed modes :
> [   59.033355] Modeline 34:"480x640" 66 22153 480 504 512 520 640 644 646
> 648 0x48 0xa
> [   59.094421] dsi: omap_plane_atomic_update vid1, crtc=eef5f800
> fb=eda4f400dsi: omap_plane_atomic_update 480x640 -> 480x640 (480)dsi:
> omap_plane_atomic_update 0,0 0xbeb00000 0x00000000dsi: dispc_ovl_setup() 1,
> pa 0xbeb00000, pa_uv 0x00000000, sw 480, 0,0, 480x640 -> 480x640, cmode 80,
> rot 0, mir 0, chan 0 repl 0
> [   59.123718] dsi: dispc_ovl_setup_common() rotation type 1 paddr beb00000
> [   59.131683] dsi: dispc_ovl_setup_common() offset0 0, offset1 0, row_inc
> 1, pix_inc 1
> [   59.140502] dsi: omap_crtc_atomic_flush() lcd
> [   59.158782] dsi: omap_crtc_atomic_flush() lcd
> [   59.174163] dsi: omap_plane_atomic_update vid1, crtc=eef5f800
> fb=eda4f400dsi: omap_plane_atomic_update 480x640 -> 480x640 (480)dsi:
> omap_plane_atomic_update 0,0 0xbeb00000 0x00000000dsi: dispc_ovl_setup() 1,
> pa 0xbeb00000, pa_uv 0x00000000, sw 480, 0,0, 480x640 -> 480x640, cmode 80,
> rot 0, mir 0, chan 0 repl 0
> [   59.203735] dsi: dispc_ovl_setup_common() rotation type 1 paddr beb00000
> [   59.211608] dsi: dispc_ovl_setup_common() offset0 0, offset1 0, row_inc
> 1, pix_inc 1
> [   59.220550] dsi: omap_crtc_atomic_flush() lcd
> [   59.234619] dsi: omap_crtc_atomic_flush() lcd
> [   61.995056] dsi: omap_crtc_atomic_flush() lcd
>
> Debian GNU/Linux 8 letux ttyO2
> letux login:
>
> Linux letux 4.6.0-rc7-letux+ #311 SMP PREEMPT Tue May 10 14:40:27 CEST
> 2016 armv7l
>
> The programs included with the Debian GNU/Linux system are free software;
> the exact distribution terms for each program are described in the
> individual files in /usr/share/doc/*/copyright.
>
> Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
> permitted by applicable law.
> root at letux:~# cat /proc/meminfo
> MemTotal:        1019140 kB
> MemFree:          747528 kB
> MemAvailable:     947892 kB
> Buffers:           11940 kB
> Cached:           205204 kB
> SwapCached:            0 kB
> Active:           154936 kB
> Inactive:          86648 kB
> Active(anon):      24524 kB
> Inactive(anon):     3056 kB
> Active(file):     130412 kB
> Inactive(file):    83592 kB
> Unevictable:           0 kB
> Mlocked:               0 kB
> HighTotal:        260096 kB
> HighFree:         201776 kB
> LowTotal:         759044 kB
> LowFree:          545752 kB
> SwapTotal:             0 kB
> SwapFree:              0 kB
> Dirty:               696 kB
> Writeback:           188 kB
> AnonPages:         24440 kB
> Mapped:            27052 kB
> Shmem:              3144 kB
> Slab:              18740 kB
> SReclaimable:       9932 kB
> SUnreclaim:         8808 kB
> KernelStack:        1416 kB
> PageTables:          788 kB
> NFS_Unstable:          0 kB
> Bounce:                0 kB
> WritebackTmp:          0 kB
> CommitLimit:      509568 kB
> Committed_AS:     167548 kB
> VmallocTotal:     245760 kB
> VmallocUsed:           0 kB
> VmallocChunk:          0 kB
> CmaTotal:          16384 kB
> CmaFree:           13460 kB
> root at letux:~#
> _______________________________________________
> Gta04-owner mailing list
> Gta04-owner at goldelico.com
> http://lists.goldelico.com/mailman/listinfo.cgi/gta04-owner
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.goldelico.com/pipermail/gta04-owner/attachments/20160511/a88c5a59/attachment-0001.html>


More information about the Gta04-owner mailing list