[Gta04-owner] Update of my GTA04 to latest production image and QtMoKo v56

[Sebastian Reinhardt]

Hello,

I read about starting support of camera and fm-transceiver, so 
Yesterday, I updated my GTA04 to this version of boot files:

http://download.goldelico.com/gta04/20130716-GTA04-Production-Universal/

This, what I have done:
1. create a SD-card with "makesd" (taken from site above, replaced the 
/dev/sdx by correct /dev/sde)
2. I booted my Moko from this card, everthing was fine. I was able to 
scan the frequencies and test the cam.
3. ./flash_nand => I flashed the new file into NAND, but I got these 
messages:
-----------------------------------
root at gta04:~# ./flash-nand
flashing Kernel
flash_eraseall has been replaced by `flash_erase <mtddev> 0 0`; please 
use it
Erasing 128 Kibyte @ 3e0000 -- 100 % complete
Writing data to block 0 at offset 0x0
..
[snip]
..
Writing data to block 24 at offset 0x300000
flashing Rootfs as UBIFS
umount: ubi0:gta04-rootfs: not found
ubiformat: mtd4 (nand), size 530055168 bytes (505.5 MiB), 4044 
eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 4043 -- 100 % complete
ubiformat: 4032 eraseblocks have valid erase counter, mean value is 5
ubiformat: 12 bad eraseblocks found, numbers: 807, 1125, 1203, 1373, 
1689, 1955, 2475, 2503, 3383, 3425, 3681, 3727
ubiformat: formatting eraseblock 889 -- 22 % complete  libmtd: error!: 
MEMERASE64 ioctl failed for eraseblock 889 (mtd4)
         error 5 (Input/output error)

ubiformat: error!: failed to erase eraseblock 889
            error 5 (Input/output error)
ubiformat: marking block 889 bad
ubiformat: formatting eraseblock 4043 -- 100 % complete
UBI device number 0, total 4031 LEBs (520095744 bytes, 496.0 MiB), 
available 3958 LEBs (510676992 bytes, 487.0 MiB), LEB size 129024 bytes 
(126.0 KiB)
Set volume size to 510676992
Volume ID 0, size 3958 LEBs (510676992 bytes, 487.0 MiB), LEB size 
129024 bytes (126.0 KiB), dynamic, name "gta04-rootfs", alignment 1
copying files (takes a while)
tar: Read checkpoint 100
..
[snip]
..
tar: Read checkpoint 48000
tar: ./dev/log: socket ignored
tar: ./boot: implausibly old time stamp 1970-01-01 00:00:00
tar: Read checkpoint 48100
tar: ./dev/pts: implausibly old time stamp 1970-01-01 00:00:00
tar: Read checkpoint 48200
tar: ./run/sdp: socket ignored
tar: ./run/dbus/system_bus_socket: socket ignored
tar: ./run/udev/control: socket ignored
tar: Read checkpoint 48300
..
[snip]
..
tar: Read checkpoint 65700
copied
patching and syncing
synced
Filesystem        1K-blocks   Used Available Use% Mounted on
rootfs             30612932 887856  28170004   4% /
/dev/root          30612932 887856  28170004   4% /
devtmpfs             244792      0    244792   0% /dev
tmpfs                 48980    352     48628   1% /run
tmpfs                  5120      0      5120   0% /run/lock
tmpfs                 97940      0     97940   0% /dev/shm
tmpfs                244892      8    244884   1% /tmp
tmpfs                244892      0    244892   0% /var/tmp
/dev/mmcblk0p1        64448   4969     59479   8% /boot
ubi0:gta04-rootfs    466452 418612     43000  91% /mnt/nand
done.
root at gta04:~#
-----------------------------
Can I ignore these error messages?

4. replaced these boot files on QtMoKo SD-Card by new ones:
------------------
bootargs.scr
boot.scr
menu.rgb16z
MLO
splash.rgb16z
u-boot.bin
u-boot.flash
uImage
x-load.flash
------------------

5. boot QtMoko

Booting QtMoko works fine, but no RF- devices are available, no Modem, 
Bluetooh, WLAN and also no USB-Connection! What is wrong?

I guess, I made any mistake, so what? Please help, because I do not like 
to flash the old version again....but I like to take calls, too.


-- 
Regards

Sebastian Reinhardt