[Letux-kernel] [RFC v3 1/9] nvmem: add driver for JZ4780 efuse

H. Nikolaus Schaller hns at goldelico.com
Sun Feb 16 20:20:43 CET 2020


From: PrasannaKumar Muralidharan <prasannatsmkumar at gmail.com>

This patch brings support for the JZ4780 efuse. Currently it only exposes
a read only access to the entire 8K bits efuse memory and nvmem cells.

Tested-by: Mathieu Malaterre <malat at debian.org>
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar at gmail.com>
Signed-off-by: Mathieu Malaterre <malat at debian.org>
Signed-off-by: H. Nikolaus Schaller <hns at goldelico.com>
(Signed-off-by: Paul Cercueil <paul at crapouillou.net>)
---
 drivers/nvmem/Kconfig        |  10 ++
 drivers/nvmem/Makefile       |   2 +
 drivers/nvmem/jz4780-efuse.c | 249 +++++++++++++++++++++++++++++++++++
 3 files changed, 261 insertions(+)
 create mode 100644 drivers/nvmem/jz4780-efuse.c

diff --git a/drivers/nvmem/Kconfig b/drivers/nvmem/Kconfig
index 35efab1ba8d9..10f8e08f5e31 100644
--- a/drivers/nvmem/Kconfig
+++ b/drivers/nvmem/Kconfig
@@ -55,6 +55,16 @@ config NVMEM_IMX_OCOTP_SCU
 	  This is a driver for the SCU On-Chip OTP Controller (OCOTP)
 	  available on i.MX8 SoCs.
 
+config JZ4780_EFUSE
+	tristate "JZ4780 EFUSE Memory Support"
+	depends on MACH_JZ4780 || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  Say Y here to include support for JZ4780 efuse memory found on
+	  all JZ4780 SoC based devices.
+	  To compile this driver as a module, choose M here: the module
+	  will be called nvmem_jz4780_efuse.
+
 config NVMEM_LPC18XX_EEPROM
 	tristate "NXP LPC18XX EEPROM Memory Support"
 	depends on ARCH_LPC18XX || COMPILE_TEST
diff --git a/drivers/nvmem/Makefile b/drivers/nvmem/Makefile
index 6b466cd1427b..65a268d17807 100644
--- a/drivers/nvmem/Makefile
+++ b/drivers/nvmem/Makefile
@@ -18,6 +18,8 @@ obj-$(CONFIG_NVMEM_IMX_OCOTP)	+= nvmem-imx-ocotp.o
 nvmem-imx-ocotp-y		:= imx-ocotp.o
 obj-$(CONFIG_NVMEM_IMX_OCOTP_SCU)	+= nvmem-imx-ocotp-scu.o
 nvmem-imx-ocotp-scu-y		:= imx-ocotp-scu.o
+obj-$(CONFIG_JZ4780_EFUSE)		+= nvmem_jz4780_efuse.o
+nvmem_jz4780_efuse-y		:= jz4780-efuse.o
 obj-$(CONFIG_NVMEM_LPC18XX_EEPROM)	+= nvmem_lpc18xx_eeprom.o
 nvmem_lpc18xx_eeprom-y	:= lpc18xx_eeprom.o
 obj-$(CONFIG_NVMEM_LPC18XX_OTP)	+= nvmem_lpc18xx_otp.o
diff --git a/drivers/nvmem/jz4780-efuse.c b/drivers/nvmem/jz4780-efuse.c
new file mode 100644
index 000000000000..ac03e1900ef9
--- /dev/null
+++ b/drivers/nvmem/jz4780-efuse.c
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * JZ4780 EFUSE Memory Support driver
+ *
+ * Copyright (c) 2017 PrasannaKumar Muralidharan <prasannatsmkumar at gmail.com>
+ * Copyright (c) 2020 H. Nikolaus Schaller <hns at goldelico.com>
+ */
+
+/*
+ * Currently supports JZ4780 efuse which has 8K programmable bit.
+ * Efuse is separated into seven segments as below:
+ *
+ * -----------------------------------------------------------------------
+ * | 64 bit | 128 bit | 128 bit | 3520 bit | 8 bit | 2296 bit | 2048 bit |
+ * -----------------------------------------------------------------------
+ *
+ * The rom itself is accessed using a 9 bit address line and an 8 word wide bus
+ * which reads/writes based on strobes. The strobe is configured in the config
+ * register and is based on number of cycles of the bus clock.
+ *
+ * Driver supports read only as the writes are done in the Factory.
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/timer.h>
+
+#define JZ_EFUCTRL			(0x0)	/* Control Register */
+#define JZ_EFUCFG			(0x4)	/* Configure Register*/
+#define JZ_EFUSTATE			(0x8)	/* Status Register */
+#define JZ_EFUDATA(n)			(0xC + (n)*4)
+
+#define JZ_EFUSE_START_ADDR		0x200
+
+#define JZ_EFUSE_EFUCTRL_CS		BIT(30)
+#define JZ_EFUSE_EFUCTRL_ADDR_MASK	0x1FF
+#define JZ_EFUSE_EFUCTRL_ADDR_SHIFT	21
+#define JZ_EFUSE_EFUCTRL_LEN_MASK	0x1F
+#define JZ_EFUSE_EFUCTRL_LEN_SHIFT	16
+#define JZ_EFUSE_EFUCTRL_PG_EN		BIT(15)
+#define JZ_EFUSE_EFUCTRL_WR_EN		BIT(1)
+#define JZ_EFUSE_EFUCTRL_RD_EN		BIT(0)
+
+#define JZ_EFUSE_EFUCFG_INT_EN		BIT(31)
+#define JZ_EFUSE_EFUCFG_RD_ADJ_MASK	0xF
+#define JZ_EFUSE_EFUCFG_RD_ADJ_SHIFT	20
+#define JZ_EFUSE_EFUCFG_RD_STR_MASK	0xF
+#define JZ_EFUSE_EFUCFG_RD_STR_SHIFT	16
+#define JZ_EFUSE_EFUCFG_WR_ADJ_MASK	0xF
+#define JZ_EFUSE_EFUCFG_WR_ADJ_SHIFT	12
+#define JZ_EFUSE_EFUCFG_WR_STR_MASK	0xFFF
+#define JZ_EFUSE_EFUCFG_WR_STR_SHIFT	0
+
+#define JZ_EFUSE_EFUSTATE_WR_DONE	BIT(1)
+#define JZ_EFUSE_EFUSTATE_RD_DONE	BIT(0)
+
+struct jz4780_efuse {
+	struct device *dev;
+	void __iomem *iomem;
+	struct clk *clk;
+	unsigned int rd_adj;
+	unsigned int rd_strobe;
+};
+
+/* We read 32 byte chunks to avoid complexity in the driver. */
+static int jz4780_efuse_read_32bytes(struct jz4780_efuse *efuse, char *buf,
+		unsigned int addr)
+{
+	unsigned int tmp = 0;
+	int i = 0;
+	int timeout = 1000;
+	int size = 32;
+
+	/* 1. Set config register */
+	tmp = readl(efuse->iomem + JZ_EFUCFG);
+	tmp &= ~((JZ_EFUSE_EFUCFG_RD_ADJ_MASK << JZ_EFUSE_EFUCFG_RD_ADJ_SHIFT)
+	| (JZ_EFUSE_EFUCFG_RD_STR_MASK << JZ_EFUSE_EFUCFG_RD_STR_SHIFT));
+	tmp |= (efuse->rd_adj << JZ_EFUSE_EFUCFG_RD_ADJ_SHIFT)
+	| (efuse->rd_strobe << JZ_EFUSE_EFUCFG_RD_STR_SHIFT);
+	writel(tmp, efuse->iomem + JZ_EFUCFG);
+
+	/*
+	 * 2. Set control register to indicate what to read data address,
+	 * read data numbers and read enable.
+	 */
+	tmp = readl(efuse->iomem + JZ_EFUCTRL);
+	tmp &= ~(JZ_EFUSE_EFUCFG_RD_STR_SHIFT
+		| (JZ_EFUSE_EFUCTRL_ADDR_MASK << JZ_EFUSE_EFUCTRL_ADDR_SHIFT)
+		| JZ_EFUSE_EFUCTRL_PG_EN | JZ_EFUSE_EFUCTRL_WR_EN
+		| JZ_EFUSE_EFUCTRL_WR_EN);
+
+	/* Need to select CS bit if address accesses upper 4Kbits memory */
+	if (addr >= (JZ_EFUSE_START_ADDR + 512))
+		tmp |= JZ_EFUSE_EFUCTRL_CS;
+
+	tmp |= (addr << JZ_EFUSE_EFUCTRL_ADDR_SHIFT)
+		| ((size - 1) << JZ_EFUSE_EFUCTRL_LEN_SHIFT)
+		| JZ_EFUSE_EFUCTRL_RD_EN;
+	writel(tmp, efuse->iomem + JZ_EFUCTRL);
+
+	/*
+	 * 3. Wait status register RD_DONE set to 1 or EFUSE interrupted,
+	 * software can read EFUSE data buffer 0 - 8 registers.
+	 */
+	do {
+		tmp = readl(efuse->iomem + JZ_EFUSTATE);
+		usleep_range(1000, 2000);
+		if (timeout--)
+			break;
+	} while (!(tmp & JZ_EFUSE_EFUSTATE_RD_DONE));
+
+	if (timeout <= 0) {
+		dev_err(efuse->dev, "Timed out while reading\n");
+		return -EAGAIN;
+	}
+
+	for (i = 0; i < (size / 4); i++)
+		*((unsigned int *)(buf + i * 4))
+			 = readl(efuse->iomem + JZ_EFUDATA(i));
+
+	return 0;
+}
+
+/* main entry point */
+static int jz4780_efuse_read(void *context, unsigned int offset,
+					void *val, size_t bytes)
+{
+	struct jz4780_efuse *efuse = context;
+	int ret;
+
+	while (bytes > 0) {
+		unsigned int start = offset & ~(32 - 1);
+		unsigned chunk = min(bytes, (start + 32 - offset));
+
+		if (start == offset && chunk == 32) {
+			ret = jz4780_efuse_read_32bytes(efuse, val, start);
+			if (ret < 0)
+				return ret;
+
+		} else {
+			char buf[32];
+			ret = jz4780_efuse_read_32bytes(efuse, buf, start);
+			if (ret < 0)
+				return ret;
+
+			memcpy(val, &buf[offset - start], chunk);
+		}
+
+		val += chunk;
+		offset += chunk;
+		bytes -= chunk;
+	}
+
+	return 0;
+}
+
+static struct nvmem_config jz4780_efuse_nvmem_config = {
+	.name = "jz4780-efuse",
+	.read_only = true,
+	.size = 1024,
+	.word_size = 1,
+	.stride = 1,
+	.owner = THIS_MODULE,
+	.reg_read = jz4780_efuse_read,
+};
+
+static int jz4780_efuse_probe(struct platform_device *pdev)
+{
+	struct nvmem_device *nvmem;
+	struct jz4780_efuse *efuse;
+	struct resource *res;
+	unsigned long clk_rate;
+	struct device *dev = &pdev->dev;
+
+	efuse = devm_kzalloc(&pdev->dev, sizeof(*efuse), GFP_KERNEL);
+	if (!efuse)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	efuse->iomem = devm_ioremap(&pdev->dev, res->start, resource_size(res));
+	if (IS_ERR(efuse->iomem))
+		return PTR_ERR(efuse->iomem);
+
+	efuse->clk = devm_clk_get(&pdev->dev, "bus_clk");
+	if (IS_ERR(efuse->clk))
+		return PTR_ERR(efuse->clk);
+
+	clk_rate = clk_get_rate(efuse->clk);
+	/*
+	 * rd_adj and rd_strobe are 4 bit values
+	 * bus clk period * (rd_adj + 1) > 6.5ns
+	 * bus clk period * (rd_adj + 5 + rd_strobe) > 35ns
+	 */
+	efuse->rd_adj = (((6500 * (clk_rate / 1000000)) / 1000000) + 1) - 1;
+	efuse->rd_strobe = ((((35000 * (clk_rate / 1000000)) / 1000000) + 1)
+						- 5 - efuse->rd_adj);
+
+	if ((efuse->rd_adj > 0x1F) || (efuse->rd_strobe > 0x1F)) {
+		dev_err(&pdev->dev, "Cannot set clock configuration\n");
+		return -EINVAL;
+	}
+	efuse->dev = dev;
+
+	jz4780_efuse_nvmem_config.dev = &pdev->dev;
+	jz4780_efuse_nvmem_config.priv = efuse;
+
+	nvmem = nvmem_register(&jz4780_efuse_nvmem_config);
+	if (IS_ERR(nvmem))
+		return PTR_ERR(nvmem);
+
+	platform_set_drvdata(pdev, nvmem);
+
+	return 0;
+}
+
+static int jz4780_efuse_remove(struct platform_device *pdev)
+{
+	struct nvmem_device *nvmem = platform_get_drvdata(pdev);
+
+	nvmem_unregister(nvmem);
+
+	return 0;
+}
+
+static const struct of_device_id jz4780_efuse_match[] = {
+	{ .compatible = "ingenic,jz4780-efuse" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, jz4780_efuse_match);
+
+static struct platform_driver jz4780_efuse_driver = {
+	.probe  = jz4780_efuse_probe,
+	.remove = jz4780_efuse_remove,
+	.driver = {
+		.name = "jz4780-efuse",
+		.of_match_table = jz4780_efuse_match,
+	},
+};
+module_platform_driver(jz4780_efuse_driver);
+
+MODULE_AUTHOR("PrasannaKumar Muralidharan <prasannatsmkumar at gmail.com>");
+MODULE_AUTHOR("H. Nikolaus Schaller <hns at goldelico.com>");
+MODULE_DESCRIPTION("Ingenic JZ4780 efuse driver");
+MODULE_LICENSE("GPL v2");
-- 
2.23.0



More information about the Letux-kernel mailing list